Rosemount 2240S Скачать руководство пользователя страница 79

Страница: 79 / 100

Reference Manual

300550EN, Rev AA
December 2010

Rosemount 2240S

www.rosemount-tg.com

Appendix A

Reference Data

A.1

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-1

A.2

Dimensional drawings . . . . . . . . . . . . . . . . . . . . . . . page A-3

A.3

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . page A-4

A.1 SPECIFICATIONS

General

Product

Rosemount 2240S Multi-Input Temperature Transmitter

Number of spot elements and wiring

Up to 16 RTD spot elements or averaging sensors can be connected to a 2240S.

Rosemount temperature / water level sensors (models 565, 566 and 765)

Three wiring types can be used:
• 3-wire

RTD with common return (1-16 spot elements)

• 3-wire RTD individual (1-16 spot elements with Rosemount 565, 1-6 spot elements

with Rosemount 566, and 1-14 spot elements with Rosemount 765)

• 4-wire RTD individual (1-16 spot elements with Rosemount 565, 1-4 spot elements

with Rosemount 566, and 1-10 spot elements with Rosemount 765)

Standard temperature sensor types

Supports Pt-100 (according to IEC/EN60751, ASTM E1137) and Cu-90

Metrology sealing possibility

Yes

Write protect switch

Yes

Hazardous location certifications

ATEX, FM-C, FM-US, and IECEx.

CE-mark

Complies with applicable EU directives (EMC, ATEX)

Ordinary location certification

Complies with FM 3810:2005 and CSA: C22.2 No. 1010.1

Measuring Performance

Temperature conversion accuracy

(1)

±0.05 °C (±0.09 °F)

Ambient temperature effect

±0.05 °C (±0.09 °F)

Temperature measuring range

Supports -200 to 250 °C (-328 to 482 °F) for Pt-100

Resolution

± 0.1 °C (± 0.1 °F) according to API chapter 7 and 12

Update time

4 s

Configuration

Configuration tool

TankMaster WinSetup is the recommended tool for easy configuration of 2240S.
The Tankbus autoconfiguration feature, handled by the Rosemount 2410 Tank Hub,
supports 2240S

Configuration parameters (examples)

Temperature:

• Number of temperature sensor elements
• Temperature element type (spot or average)
• Temperature element position in tank

Water Level Sensor:

• Level offset (difference between tank zero level and water zero level)
• Probe length (autoconfigured by Rosemount 765)

Output variables and units

Spot and average temperature: °C (Celsius), and °F (Fahrenheit)
Free water level (FWL): meter, centimeter, millimeter, feet, or inch

Содержание 2240S





































































































Результаты поиска

Содержание 2240S

Отзывы:

Похожие инструкции для 2240S

Бренды по названию

Популярные бренды

Rosemount 2240S, Справочное руководство

Результаты поиска

Содержание 2240S

Отзывы:

Похожие инструкции для 2240S

Бренды по названию

Популярные бренды