background image

9

Recommended Service Intervals

R e c o m m e n d e d   S e r v i c e   I n t e r v a l s

Regular service is required to keep your RockShox® product working at peak performance. Follow this maintenance schedule and install the service parts 

included in each service kit that corresponds with the Service Hours Interval recommendation below. For spare part kit contents and details, refer to the 

RockShox Spare Parts Catalog at 

www.sram.com/service

.

Service Hours Interval

Maintenance

Benefit

Every ride

Clean dirt from upper tubes and wiper seals.

Extends wiper seal lifespan

Minimizes damage to upper tubes

Minimizes lower leg contamination

Every 50 Hours

Perform lower leg service

Restores small bump sensitivity

Reduces friction

Extends bushing lifespan

Every 200 Hours

Perform damper and spring service

Extends suspension lifespan

Restores small bump sensitivity

Restores damping performance

R e c o r d   Y o u r   S e t t i n g s

Use the charts below to record your fork settings to return your fork to its pre-service settings. Record your service date to track  

service intervals. 

Service Hours Interval

Date of Service

Air Pressure

Rebound setting - count the 

number of clicks while turning 

the rebound adjuster fully 

counter-clockwise. 

Compression setting - count the 

number of clicks while turning the 

compression adjuster fully counter-

clockwise.

50

100

150

200

T o r q u e   V a l u e s

Part

Tool 

Torque

Bottom bolts

5 mm hex bit 

6.8 N•m (60 in-lb)

Bottomless Tokens™

8 mm and 24 mm or RockShox Top Cap / 

Cassette Lockring Tool

3.4-4.5 N•m (30-40 in-lb)

Top caps

24 mm or RockShox Top Cap / Cassette 

Lockring Tool

12.4 N•m (110 in-lb)

O i l   V o l u m e   a n d   O i l   H e i g h t

Lower Leg

Upper Tube

Fork

Model

Travel (mm)

Suspension Oil

Volume (mL)

Suspension Oil

Volume  

+/- 2 (mL)

Oil Height (mm) 

Bluto™

RCT3   

RL

80-120

15wt

5

5wt

108

70-75

Reba®

RL

80-100

100

110-120

108

130-150

136

Содержание Bluto

































Отзывы: