manualshive.com logo in svg

Ricoh G031, Руководство по обслуживанию

Ricoh G031 - качественная модель принтера с многофункциональными возможностями. Для получения бесплатного руководства по обслуживанию и ремонту, загрузите Service Manual с нашего вебсайта. Никаких скрытых платежей, просто надежная информация для вашего устройства от manualshive.com.

Поделиться
Скачать
background image

2000 RICOH Corporation. All rights reserved.

CONTROL NO. 043ABW

TECHNICAL SERVICE BULLETIN

TECHNICAL SERVICE BULLETIN

TECHNICAL SERVICE BULLETIN

TECHNICAL SERVICE BULLETIN

BULLETIN NUMBER:

BULLETIN NUMBER:

BULLETIN NUMBER:

BULLETIN NUMBER:

G031/G032/G049/G054 – 01

G031/G032/G049/G054 – 01

G031/G032/G049/G054 – 01

G031/G032/G049/G054 – 011

1

1

1

0

0

0

07/05/2000

7/05/2000

7/05/2000

7/05/2000

This bulletin was originally issued as G031/G032/G049/G054 – 010.

This bulletin was originally issued as G031/G032/G049/G054 – 010.

This bulletin was originally issued as G031/G032/G049/G054 – 010.

This bulletin was originally issued as G031/G032/G049/G054 – 010.

APPLICABLE MODEL

APPLICABLE MODEL

APPLICABLE MODEL

APPLICABLE MODEL::::
    GESTETNER – P7021/P7016

    GESTETNER – P7021/P7016

    GESTETNER – P7021/P7016

    GESTETNER – P7021/P7016
    RICOH – AP2100/AP1600

    RICOH – AP2100/AP1600

    RICOH – AP2100/AP1600

    RICOH – AP2100/AP1600
    SAVIN – SLP21/SLP16

    SAVIN – SLP21/SLP16

    SAVIN – SLP21/SLP16

    SAVIN – SLP21/SLP16

SUBJECT:

PARTS CATALOG UPDATES

GENERAL:

The following information is to supply the technician with the new part numbers for the G049 and G054
printers. Since nearly all of the components of the G049 and G054 are the same as the G031 and G032,
only those parts that are different will be described in this bulletin. The G049 information is placed into the
G031 portion of the Parts Catalog and the G054 information is placed into the G032 portion of the Parts
Catalog. The following parts updates are being issued for all G031/G032/G049/G054 Parts Catalogs.

•

UPDATE 1:

G049 only Page 7

REFERENCE

PART NUMBER

DESCRIPTION

QTY

PAGE

ITEM

G0292698

By-Pass Feed Unit – EU – (G049)

1

7

1

G0292721

Manual Feed Table – EU – (G049) (Ricoh)

1

7

9

G0291420

Control Panel – US – (G049)

1

7

13

G0291421

Control Panel – EU – (G049)

1

7

13

G049 only Page 17

REFERENCE

PART NUMBER

DESCRIPTION

QTY

PAGE

ITEM

G0295125

Engine Control Board – 120V – (G049)

1

17

8

G0295130

Engine Control Board – 230V – (G049)

1

17

8

G0315700

Main control Board – (G049)

1

17

9

G049 only Page 23

REFERENCE

PART NUMBER

DESCRIPTION

QTY

PAGE

ITEM

G0495700

Main Control Board – (G049)

1

23

❇

G0415904

IC – ASIC ROCKY_Z – (G049)

1

23

1

G0415903

Oscillator – (G049)

1

23

2

G049 only Page 27

REFERENCE

PART NUMBER

DESCRIPTION

QTY

PAGE

ITEM

G0295125

Engine Control Board – 120V – (G049)

1

27

❇

G0295130

Engine Control Board – 230V – (G049)

1

27

❇

G0295170

IC – UVEPROM 1MX8 100NS – (G049)

1

27

1

G0295171

IC – UVEPROM 1MX8 100NS – (G049)

1

27

2

Continued…

Note:

T

his

c

opy

is
intended

as
a

m

aster

o

riginal

for

reproduction

of
additional

bulletins.

!

PARTS

G049 Newly Added Parts –

The following G049 parts updates are

being added to the G031 section of the Parts Catalog. Please update
your Parts Catalog with the following information.

Содержание G031


























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G031

Oki C910 Service Manual preview
C910
Бренд: Oki Страницы: 282
MakerPi P2 Quick Start Manual preview
P2
Бренд: MakerPi Страницы: 21
Eaton Power Defense PD3 Mounting And Operating Instructions preview
Power Defense PD3
Бренд: Eaton Страницы: 4
Samsung SCX 4500W - Personal Wireless Laser Multi-Function... User Manual preview
SCX 4500W - Personal Wireless Laser Multi-Function...
Бренд: Samsung Страницы: 113
Canon imageRUNNER ADVANCE 8105 Specification preview
imageRUNNER ADVANCE 8105
Бренд: Canon Страницы: 5
Canon imageCLASS MF269dw Setup Manual preview
imageCLASS MF269dw
Бренд: Canon Страницы: 32
Samsung ML-7300N User Manual preview
ML-7300N
Бренд: Samsung Страницы: 158
DataSouth Documax A6300 Series User Manual preview
Documax A6300 Series
Бренд: DataSouth Страницы: 180
Ricoh P 501 Setup Manual preview
P 501
Бренд: Ricoh Страницы: 24
Kyocera C5020N - FS Color LED Printer Command Reference Manual preview
C5020N - FS Color LED Printer
Бренд: Kyocera Страницы: 410
LulzBot TAZ 6 Operation Manual preview
TAZ 6
Бренд: LulzBot Страницы: 3
3D Printing Systems UP Plus 3D Manual preview
UP Plus 3D
Бренд: 3D Printing Systems Страницы: 56
Jolimark NP311D Instruction Manual preview
NP311D
Бренд: Jolimark Страницы: 31
123inkt DR-L3 User Manual preview
DR-L3
Бренд: 123inkt Страницы: 73
Tinkerine Studio Ditto Pro Setup & Operation Manual preview
Ditto Pro
Бренд: Tinkerine Studio Страницы: 17
Canon imagePROGRAF TM-355 Manual preview
imagePROGRAF TM-355
Бренд: Canon Страницы: 52
Epilog Laser Legend 6000 Owner'S Manual preview
Legend 6000
Бренд: Epilog Laser Страницы: 92
WOOSIM PORTI-P340 Operator'S Manual preview
PORTI-P340
Бренд: WOOSIM Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды