Ricoh Aficio FX10 Скачать руководство пользователя страница 230

Страница: 230 / 284

4. Skew

Possible Cause:

•

A non-recommended type of paper is being used.

•

Incorrect positioning of the paper guides in the paper cassette.

•

The corner separators are out of position.

•

The paper feed rollers are worn out or damaged.

•

Obstruction in the paper path.

•

Malfunction in the registration mechanism.

Action:

1. Check if a correct type of paper is being used.

2. Check that the paper guides and the corner separators in the paper cas-

sette are correctly set.

3. Check that the paper feed rollers are correctly installed and clean or re-

place them if necessary.

4. Check for obstructions in the paper path.

5. Check the registration mechanism and clean or replace the rollers if nec-

essary.

5. Multi-feed

Possible Cause:

•

A non-recommended type of paper is being used.

•

Incorrect positioning of the paper guides and/or end fence in the paper
cassette.

Action:

•

Check if a correct type of paper is being used.

•

Check that the paper guides and the end fence are correctly set.

roub

oot

June 10th, 1997

TROUBLESHOOTING

MECHANICAL PROBLEMS

7-25

Содержание Aficio FX10





























































































































































































































































































Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды

Ricoh Aficio FX10, Руководство по обслуживанию

Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды