Ricoh Aficio FX10 Скачать руководство пользователя страница 223

Страница: 223 / 284

7.2. MECHANICAL PROBLEMS

7.2.1. ADF

1. Non Feed

Possible Cause:

•

An incorrect type or size of document is used.

•

The ADF roller assembly is not properly installed.

•

The pick-up and feed rollers are dirty or worn out.

•

The mechanical clutch mechanism for document pick-up is defective.

•

The ADF motor is defective.

•

The platen cover sensor is defective.

Action:

1. Check that a correct type of document is being used.

2. Check that the ADF roller assembly is properly installed. Replace the as-

sembly if it is damaged.

3. If the problem still remains, do the following.

•

Clean the pick-up and feed rollers with a soft cloth and water, and re-
place them if they are damaged.

•

Check the spring mechanism of the pick-up roller and replace it if it is
damaged.

•

Check the connection between the FCU (CN62) and the ADF motor.

•

Check that the platen cover sensor is working properly and replace if it
is damaged.

•

Replace the ADF motor.

TROUBLESHOOTING

June 10th, 1997

MECHANICAL PROBLEMS

7-18

Содержание Aficio FX10





























































































































































































































































































Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды

Ricoh Aficio FX10, Руководство по обслуживанию

Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды