Ricoh Aficio FX10 Скачать руководство пользователя страница 208

Страница: 208 / 284

7.1.2. Black Copies

Possible Cause (Scanner)

•

The contact image sensor is defective.

•

The xenon lamp, or the xenon lamp driver is defective.

Action:

1. Check the connection between the FCU (CN60) and the contact image

sensor.

2. Do the ADF lamp test (service function 10) and check that the xenon

lamp is working properly.

3. Check that the two springs which push up the contact image sensor

against the exposure glass are correctly installed.

4. Replace the contact image sensor.

Possible Cause (Printer)

•

The charge is not properly applied.

Action:

1. Check if all the charge bias terminals on the development unit and the

CTM, and the charge wire are properly connected or not.

•

If they are, go to step 2.

•

If not, fix the connections.

2. Check if the zener diode is not shorted.

•

If the zener diode is shorted, replace the zener diode.

•

If it is not, go to step 3.

3. Check the connections behind the power pack.

roub

oot

June 10th, 1997

TROUBLESHOOTING

COPY QUALITY TROUBLESHOOTING

7-3

Содержание Aficio FX10





























































































































































































































































































Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды

Ricoh Aficio FX10, Руководство по обслуживанию

Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды