Ricoh Aficio FX10 Скачать руководство пользователя страница 228

Страница: 228 / 284

2. Paper Jam - Inside the Printer

Possible Cause:

•

A non-recommended type of paper is being used.

•

The paper end fence and/or the paper guides in the cassette is not prop-
erly set.

•

The registraton roller is dirty.

•

The registration sensor is defective.

•

Obstruction in the paper path.

•

The main motor is defective.

Action:

1. Check if a correct type of paper is being used, and check that the paper

end fence and the paper guides are correctly set.

2. Check for obstructions in the paper path.

3. Check the registration roller and its mechanism. Clean or replace if neces-

sary.

4. Check that the registration sensor is working properly.

5. If the problem still remains, do the following.

•

Check the connections between the FCU (CN15) and the main motor.

•

Replace the main motor.

•

Check the fusing unit drive mechanism. Check that all the gears are
properly installed.

roub

oot

June 10th, 1997

TROUBLESHOOTING

MECHANICAL PROBLEMS

7-23

Содержание Aficio FX10





























































































































































































































































































Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды

Ricoh Aficio FX10, Руководство по обслуживанию

Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды