Ricoh Aficio FX10 Скачать руководство пользователя страница 222

Страница: 222 / 284

7.1.16. Misaligned Output (Data shifted to the right or left)

Possible Cause (Scanner)

•

Incorrect setting of the document guide.

Action:

•

Align each side of the document to the document guides.

Possible Cause (Printer)

•

The laser optics are misaligned.

•

Improper print margin setting (main scan direction).

Action:

•

Adjust the main scan print margin. (Refer to Section 5-12.)

•

Check that the laser optics are aligned correctly.

7.1.17. Misaligned Output (Image shifted vertically)/Reduced Image

Possible Cause:

•

Improper print margin (sub scan direction).

•

Dirty registration roller.

Action:

•

Adjust the sub scan print margin. (Refer to Section 5-12.)

•

Clean the registration roller.

roub

oot

June 10th, 1997

TROUBLESHOOTING

COPY QUALITY TROUBLESHOOTING

7-17

Содержание Aficio FX10





























































































































































































































































































Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды

Ricoh Aficio FX10, Руководство по обслуживанию

Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды