Ricoh Aficio AP2700 Скачать руководство пользователя страница 23

Страница: 23 / 165

1 October, 1999

ELECTRICAL COMPONENT DESCRIPTIONS

1-9

Overall

Information

1.6 ELECTRICAL COMPONENT DESCRIPTIONS

Refer to the electrical component layout on the reverse side of the point-to-point
diagram for the location of the components.

Symbol

Name

Function

Motors

Polygonal Mirror

Turns the polygonal mirror.

Main Motor

Drives the main unit components.

Exhaust Fan

Removes heat from around the fusing unit.

Upper Paper Lift

Raises the bottom plate in the 1st paper tray.

Lower Paper Lift

Raises the bottom plate in the 2nd paper tray.

Toner Supply

Rotates the toner bottle to supply toner to the
development unit.

Magnetic Clutches

MC1

Upper Paper Feed

Starts paper feed from the 1st paper tray.

MC2

Lower Paper Feed

Starts paper feed from the 2nd paper tray.

MC3

Upper Paper Transport

Drives the upper transport rollers.

MC4

Lower Paper Transport

Drives the lower transport rollers.

MC5

Registration

Drives the registration rollers.

Switches

SW1

Main Switch

Provides power to the machine. If this is off,
there is no power supplied to the machine.

SW2

Right Upper Cover

Detects whether right upper cover is open or not.

SW3

Right Cover

Cuts the +5VLD and +24V dc power line and
detects whether the right cover is open or not.

SW4

Right Lower Cover

Detects whether right lower cover is open or not.

SW5

Upper Paper Size

Determines what size of paper is in the upper
paper tray.

SW6

Lower Paper Size

Determines what size of paper is in the Lower
paper tray.

SW7

Special Paper

Determines the special paper is in the lower
paper tray.

SW8

New PCU Detect

Detects when a new PCU is installed.

SW9

Front Cover Safety

Cuts the +5VLD and +24V dc power line and
detects whether the front cover is open or not.

Sensors

Toner Density (TD)

Detects the amount of toner inside the
development unit.

1st Paper End

Informs the CPU when the 1st paper tray runs
out of paper.

1st Paper End

Informs the CPU when the 2nd paper tray runs
out of paper.

Image Density (ID)

Detects the density of various patterns and the
reflectivity of the drum for process control.

Paper Overflow

Detects paper overflow condition.

Paper Exit

Detects misfeeds.

Upper Relay

Detects misfeeds.

Содержание Aficio AP2700






































































































































































Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды

Ricoh Aficio AP2700, Руководство по обслуживанию

Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды