Ricoh Aficio AP2700 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 165

background image

SOFTWARE ACCESSORIES

1 October, 1999

1-4

1.2 SOFTWARE

ACCESSORIES

The printer drivers and utility software are provided on one CD-ROM. An auto-run
installer allows you to select which components to install. The service tools are not
provided on the CD-ROM.

1.2.1 PRINTER DRIVERS

Printer Language

Windows 3.1x Windows 95/98 Windows NT4.0

Macintosh

PCL 6

Yes

Yes

Yes

No

PCL 5e

Yes

Yes

Yes

No

PS3

Yes

Yes

Yes

Yes

NOTE: 1) The printer drivers for Windows NT 4.0 are only for the Intel x86

platform. There is no Windows NT 4.0 printer driver for PowerPC, Alpha,
or MIPS platforms.

2) The PS3 drivers are all genuine AdobePS drivers. A PPD file for each

operating system is provided with the driver.

3) The PS3 drivers for Macintosh support Mac OS 7.1 or later versions.
4) The PS3 drivers for Windows 3.1x and Windows NT4.0 do not support

the “Proof Print” function.

1.2.2 UTILITY SOFTWARE

Software

Description

Agfa Font Manager
(Win3.1x, 95/98, NT4)

A font management utility with screen fonts for the printer.

Aficio Manager for Admin
(Win 95/98, NT4)

A printer management utility for network administrators. NIB
setup utilities are also available.

Aficio Manager for Client
(Win95/98, NT4)

A printer management utility for client users.

Multi-Direct Print
(Win95/98, NT4)

A utility for peer-to-peer printing over a NetBEUI or TCP/IP
network.

Port Navi
(Win95/98, NT4)

A peer to peer print utility over a TCP/IP network. This
provides parallel printing and recovery printing function.

1.2.3 SERVICE TOOLS

Software

Description

NBTFTP

NIB firmware update utility for use on a NetBEUI network.
This utility is not on the Driver and Utilities CD-ROM; it is
issued separately as a service tool

«
...
16
17
18
19
20
...
»

Содержание Aficio AP2700






































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aficio AP2700

Бренд: 3D Systems Страницы: 26

Бренд: 3D Systems Страницы: 39

WorkSeries 200 Series

Бренд: 3D Platform Страницы: 9

Бренд: EasyThreed Страницы: 15

Бренд: oliser Страницы: 6

Бренд: Wasp Страницы: 2

Бренд: Roland Страницы: 44

Бренд: Ricoh Страницы: 152

Бренд: NEC Страницы: 7

Бренд: A&D Страницы: 8

Бренд: Xerox Страницы: 2

Бренд: Oce Страницы: 230

490ST - Document Centre B/W Laser Printer

Бренд: Xerox Страницы: 322

WorkCentre XD130DF

Бренд: Xerox Страницы: 1

DocuCentre-VI C2264

Бренд: Fuji Xerox Страницы: 129

Бренд: TierTime Страницы: 35

Бренд: Graphic Products Страницы: 28

STREAM MK3 Series

Бренд: VOLUMIC Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды