Ricoh Aficio AP2700 Скачать руководство пользователя страница 156

Страница: 156 / 165

1 October, 1999

PRINTER CONTROLLER ERROR

7-11

Trouble-

shooting

7.2 PRINTER CONTROLLER ERROR

7.2.1 ERROR CODES

Code

Description

Required Action

0201

On-board SDRAM read/verify
failed.

Replace the controller if this error is
frequent.

0301

SDRAM DIMM (option)
read/verify failed.

Replace the SDRAM DIMM if this error is
frequent.

1101

Data transmission did not finish
within the specified time.

An incompatible loop-back connector is
connected to the parallel port, or the
loop-back connector is not connected.
Use the correct loop-back connector
(P/#: G0219350) before the test.

1102

Data looped back to the controller
is not the same as the data
transmitted.

The loop-back connector may be
defective. Try using another one.

11xx

Parallel interface error.

Replace the controller if this error is
frequent.

1401

The controller NVRAM has a
problem.

1402

NVRAM checksum error or the
battery has run out.

1403

NVRAM write error

1404

NVRAM read error

Replace the NVRAM if this error is
frequent.

1501

RTC error

Replace the controller board if this error
is frequent.

1601

Font ROM error

Replace the controller if this error is
frequent.

1602

The data in the Font ROM is
damaged.

Replace the controller if this error is
frequent.

1Bxx

Option bus error A

Check the connection to the optional
component.
Try replacing the optional NIB or HDD.

1Cxx

Option bus error B

Check the connection to the optional
component.
Try replacing the optional NIB or HDD.

2100

NIB self test failed.

Turn off the machine and turn it back on.
Replace the NIB if this error is frequent.

21xx

NIB error

2501

The data in the PS DIMM is
damaged.

Replace the PS DIMM if this error is
frequent.

2508

The data in the IC card is
damaged.

Reprogram the IC card and try again.

3002

A damaged cluster was found on
the HDD.

The damaged cluster is automatically
marked as “bad”.
If this error is frequent, format the HDD.

47xx

Controller ASIC error.

Replace the controller.

Содержание Aficio AP2700






































































































































































Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды

Ricoh Aficio AP2700, Руководство по обслуживанию

Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды