Ricoh Aficio AP2700 Скачать руководство пользователя страница 109

Страница: 109 / 165

1 October, 1999

SERVICE TOOLS

4-23

Service

Tables

4.5 SERVICE TOOLS

4.5.1 SERVICE TOOL MENU

Service Mode (Service Tool)

Title

Description

HDD Test

Verifies the FAT and directory entries on the
HDD.

HDD format

Partitions and formats the HDD.

NIB read/write

Backs up the NIB NVRAM and restores it.

NOTE: Items related to the HDD will not be displayed if the HDD is not installed.

4.5.2 HDD TEST

This verifies the file and directory entries on the hard disk drive.

1. Enter the SP mode, and select “3. Service Tool.”

2. Select “HDD Test”, then press [Enter].

3. Specify the number of tests, then press [Enter].

•

If “000” is specified, the test will continue until it is manually cancelled.

•

[

▲

] [

▼

]: Increment/decrement the digit at the cursor.

•

[Escape]: Exit without executing the test. Cancels the test even while it is

being executed.

•

[Enter]: Perform the test.

4. Check the result of the test, then do the following:

•

If the result is OK, press [Enter] to display the available free space on the

HDD. Then press [Enter] again to exit.

•

If the result is NG, press [Enter] to do the test again. Or, press [Cancel] to

exit.

Error Display Details
Number at the top right corner

Indicates that the error was found in the n’th
test.

Error Message

“Clstr error”
A damaged cluster was found. The damaged
cluster was marked as “bad” to avoid future use.

Содержание Aficio AP2700






































































































































































Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды

Ricoh Aficio AP2700, Руководство по обслуживанию

Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды