Ricoh Aficio AP2700 Скачать руководство пользователя страница 143

Страница: 143 / 165

PCBS AND MOTORS

1 October, 1999

6-26

6.8.3 PRINTER CONTROLLER / NIB

Printer Controller

1. Remove the controller cover [A] (6 screws).

2. Remove the network interface board [B] (2 screws).

3. Remove the printer controller board [C] (6 screws, 1 connector).

4. Remove the NVRAM from the controller board, then install them on the new

controller.

5. Install the new controller.

6. Turn on the machine and print the Printer Configuration Page.

7. Ensure that all the controller settings are restored.

NIB

1. Back up the NIB NVRAM to the controller using the Service Tool.

2. Remove the controller cover [A] (6 screws).

3. Replace the network interface board [B] (2 screws).

4. Turn on the machine and restore the NIB NVRAM using the Service Tool.

5. Turn off the machine and turn it back on. Then, print the Printer Configuration

Page.

6. Ensure the all the controller settings are restored.

G038R510.WMF

[A]

[B]

[C]

Содержание Aficio AP2700






































































































































































Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды

Ricoh Aficio AP2700, Руководство по обслуживанию

Результаты поиска

Содержание Aficio AP2700

Отзывы:

Похожие инструкции для Aficio AP2700

Бренды по названию

Популярные бренды