Rice Lake MSI-8000 Скачать руководство пользователя страница 37

Страница: 37 / 50

ScaleCore Connect

Rice Lake Weighing Systems

●

Stream Port Setup

To configure communications stream ports:

1. Select

Communications

, then

Configure

2. Select the port to be configured and press

Figure 3-31. Communication Setup

3. Set the option:

•

Baud Rate

– rate at which information is transferred through the port

Selections: 9600 (default), 19200, 38200, 57600, 115200

•

Hand Shake

– Signals transmitted back and forth over a communications network in order to establish a valid

connection between two stations.

Example: A hardware handshake uses dedicated wires like request-to-send (RTS) and clear-to-send (CTS) lines

in an RS-232 serial transmission

Selections: None, RTS/CTS, XON/XOFF (default)

•

Parity

– error detection technique that tests the integrity of digital data in the computer

Selections: None (default), ODD, EVEN

•

Data Bits

– number of bits used to represent one character of data

Selections: 7 data bits, 8 data bits (default)

•

Stop Bits

– indicates end of a character or of the whole transmission

Selections: 1 stop bit (default), 2 stop bits

4. Press

to save and return to Communication Setup.

5. Press

to return to main page.

Содержание MSI-8000



















































Результаты поиска

Содержание MSI-8000

Отзывы:

Бренды по названию

Популярные бренды

Rice Lake MSI-8000, Техническое руководство

Результаты поиска

Содержание MSI-8000

Отзывы:

Бренды по названию

Популярные бренды