manualshive.com logo in svg

Rice Lake MSI-8000, Техническое руководство

Поделиться
Скачать
Rice Lake MSI-8000 Скачать руководство пользователя страница 35

ScaleCore Connect

© 

Rice Lake Weighing Systems 

●

 All Rights Reserved

31

3.3 Advanced Setup

This section is a guide for the advanced setup of the product being read by the 

ScaleCore Connect

 program. The following 

setup instructions are for dealers or service technicians only. Please contact Rice Lake Weigh Systems or a local dealer for 

assistance before proceeding.
Prior to making changes to a product profile it is recommended to save a backup. See 

Acquire Profile from Device on page 35

.

At anytime during set up, press 

 to return to previous page without saving.

3.3.1 File Menu

The 

File Menu

 is used to open an existing profile or exit the program.

Figure 3-26. File Menu Selections

Open Profile

Profiles can be exported and saved, then imported into a different product. To open a previously saved profile:

1. Select 

File

, then 

Open Profile

.

2. Navigate to where the profile is stored.

3. Select the file and press 

. A valid profile file then displays on the left panel, under Device Profile.

4. Select the intended profile from the left panel. Application displays all information as if it was that device.

 

  The profiles that show up grayed out are read only.

To clone the open profile see 

Clone Profile to Device on page 35

.

Exit

To close 

ScaleCore Connect

 application.

Note

Содержание MSI-8000



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды