Rice Lake MSI-8000 Скачать руководство пользователя страница 27

Страница: 27 / 50

ScaleCore Connect

Rice Lake Weighing Systems

●

Min Sensor Value

– enter min sensor value acceptable

Max Sensor Value

– enter max sensor value acceptable

Not Filtered Sensor Value

– check box is applicable

DAC Offset

– current calibration value

DAC Gain

– current calibration value

DAC Count

– current calibration value

Min DAC Count

– enter min DAC Count acceptable

Max DAC Count

– enter max DAC Count acceptable

Output Mode

– select output mode to be used

Figure 3-10. Output Mode Selections

3. Press

to save.

RF Configuration

Radio Frequency (RF) configuration allows the setup of RF cards available in the products connected.

Figure 3-11. RF Configuration

1. Select

Configuration

, then

2. Enter the following parameters:

Status

– select Enabled (default) or Disabled

Channel

– select a channel from 12-23

Network ID

– enter a number from 0-65534 for an ID

Device Type

– select XBee or Other (for all other cards installed)

Power Level

– select a level from 0-4 (only on transmitters; power level does not change on receivers)

Always On

– select Enabled or Disabled (default)

Only set Always On to Enabled when using Rugged Remote. Having this parameter set to Enabled will drain the

battery even when the scale if off. Disconnect the battery when not in use.

3. Press

to save. New settings will not take affect until power is cycled on the product.

Note

Содержание MSI-8000



















































Результаты поиска

Содержание MSI-8000

Отзывы:

Бренды по названию

Популярные бренды

Rice Lake MSI-8000, Техническое руководство

Результаты поиска

Содержание MSI-8000

Отзывы:

Бренды по названию

Популярные бренды