RHEONIK RHE 07 Скачать руководство пользователя страница 6

Страница: 6 / 50

RHEONIK Messgeräte GmbH

REV. I, Apr. 2004

Operation Manual RHE 07, 08, 11

Page

1. Installation and operating instructions

1.1. General system description

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series

transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to

the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor

articles are available in non Ex-versions (without Ex-nameplate).

The RHE 11 (EEx d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2).

Ex-series sensors RHM (with Ex-Label) are, when connected with a Ex- Transmitter, made for installa-

tion inside hazardous areas (Ex-zone 0, 1 or 2).

The transmitter RHE includes seven printed boards which can be replaced during servicing.

The remote electronic unit consists of two bent measuring loops in the shape of an omega.

1.2 Installation instructions for sensor RHM

For liquids, install the sensor RHM at lowest practical level in your pipe line system. This stops gas

bubbles from collecting in the sensor.

Installation example:

RHM

The piping system must be as free of vibration as possible. Normal building and plant vibration has no

effect on meter performance. However do not mount the sensor in areas having abnormally high

vibration.

see also the following informations for Sensor installation

Содержание RHE 07



















































Результаты поиска

Содержание RHE 07

Отзывы:

Похожие инструкции для RHE 07

Бренды по названию

Популярные бренды

RHEONIK RHE 07, Руководство по эксплуатации

Результаты поиска

Содержание RHE 07

Отзывы:

Похожие инструкции для RHE 07

Бренды по названию

Популярные бренды