RHEONIK RHE 07 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 50

background image

RHEONIK Messgeräte GmbH

REV. I, Apr. 2004

.

Operation Manual RHE 07, 08, 11

Page

11

NOTES FOR INTRINSICALLY SAFE INSTALLATION

Only equipment with safety agency labels attached to the sensor and transmitter meet the
agency approval requirements.
Intrinsically safe flow meters must be installed according to the wiring diagram, supplied with
the meter.
Observe proper earth ground wiring according to this diagram.
Sensor cable must be suitable for the sensor operating temperature range.
All intrinsically safe cables must be installed separated from all other cables.
Observe temperature class and maximum allowable sensor temperature, indicated on sensor
type label, for safe operation.
All electrical installations must comply with national and local codes.

1.4. Installation instructions for the RHE flow transmitter

Install the RHE unit in an area where the ambient temperature falls within the range

-40°C .. +60°C. For installations outside this range please consult the manufacturer.

Locations with extreme vibrations must be avoided.

Do not locate the flow transmitter in direct sunlight.

Sensor RHM and transmitter RHE were calibrated together at the factory.
Therefore make sure that the serial numbers of connected systems comply with
serial numbers indicated on instrument type labels.

1.5. Power supply wiring

The remote electronic unit RHE is delivered set up for 230 VAC, 115 VAC or 24 VDC power input.

The power supply must be turned off while wiring to the remote unit RHE ...

Power supply v-10% must correspond to the voltage indicated on electronic type label or in

the power supply wiring compartment.

The earth grounding of the power supply must be connected to the RHE power supply wiring section.

Failure to connect earth ground will nullify the intrinsic safety !

«
...
9
10
11
12
13
...
»

Содержание RHE 07



















































Отзывы:

Нет отзывов

Похожие инструкции для RHE 07

Бренд: Kawai Страницы: 70

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 19

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: QALCOMET Страницы: 52

Бренд: velocomp Страницы: 4

Бренд: Hach Страницы: 96

Бренд: Hilti Страницы: 31

Бренд: Kawai Страницы: 2

Бренд: Sagola Страницы: 16

Бренд: KEM Страницы: 49

Бренд: F&F Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды