RHEONIK RHE 07 Скачать руководство пользователя страница 35

Страница: 35 / 50

RHEONIK Messgeräte GmbH

REV. I, Apr. 2004

Operation Manual RHE 07, 08, 11

Page

6.4. Examples with explanation

Example 1:

We have a 1 stage batch process (1 batch valve) and want to batch a quantity of 100 kg:

Pset

to be set on 100 kg

Pwarn

to be set on an estimated value depending on the delay time i.e.: 2 kg

If the option aoc (automatic overflow control) is not activated the

Pwarn

value will always be acti-

vated at 98 kg and will close the valve. The

Pset

output will not be connected to any valve in this

configuration.

If "

aoc

" is active, the

Pwarn

value will be controlled or optimized automatically in such a way that the

Pset

value will be reached after several batches.

Example 2:

We have a 2 stage batch process with one valve for the main flow and 1 valve for the small flow. The

output for

Pset

will be connected to the small flow valve and the output for

Pwarn

to the main flow

valve.

Pset

to be set to 100 kg

Pwarn

to be set to an estimated value depending on the delay time i.e.: 2 kg

The "

aoc

" can not be activated now !

The main flow valve will close at 98 kg and the small flow valve will close at 100 kg. This means that

still a very small overflow will appear. This can be eliminated by changing the

Pset

value to a smaller

corresponding value.

6.5. Serial interface and batch option

In addition to the standard serial interface requests and actions there are additional codes that can be

used with option code "batch" active only.

requests:

format:

Preset

value:

7FH,7FH, ’#’ , <A> , ’BRs’ , ’?’ ,0D,0A,7FH,7FH

Prewarn

value:

7FH,7FH, ’#’ , <A> , ’BRw’ , ’?’ ,0D,0A,7FH,7FH

write

Preset

value:

7FH,7FH, ’#’ , <A> , ’BWsXXXXXXXEE’ ,0D,0A,7FH,7FH

write

Prewarn

value:

7FH,7FH, ’#’ , <A> , ’BWwXXXXXXXEE’ ,0D,0A,7FH,7FH

‘0’ , ‘1’ , ... ’9’ or ‘.’

EE:

mass unit characters i.e. ‘kg’

Actions:

batch

Start

7FH,7FH, ’#’ , <A> , ’Bst’ ,0D,0A,7FH,7FH

batch

Stop

7FH,7FH, ’#’ , <A> , ’Bsp’ ,0D,0A,7FH,7FH

batch

Clear

: *

)

7FH,7FH, ’#’ , <A> , ’Bsc’ ,0D,0A,7FH,7FH

)

not for program versions before 1.24 (M221299)

Содержание RHE 07



















































Результаты поиска

Содержание RHE 07

Отзывы:

Похожие инструкции для RHE 07

Бренды по названию

Популярные бренды

RHEONIK RHE 07, Руководство по эксплуатации

Результаты поиска

Содержание RHE 07

Отзывы:

Похожие инструкции для RHE 07

Бренды по названию

Популярные бренды