RHEONIK RHE 07 Скачать руководство пользователя страница 5

Страница: 5 / 50

RHEONIK Messgeräte GmbH

REV. I, Apr. 2004

Operation Manual RHE 07, 08, 11

Page

Installation RHM XX

Wiring

RHM XX - RHE XX

Bubble Free
filling of RHM XX

Zeroing
procedure

Start with
measurement

This is a short version, please read also our Field Manual

- proper support at both sides of

the sensor required - see manual
- avoid installation at locations with
high levels of vibrations or strong

electrical fields

- wiring of RHE XX according to
our manual - attention :

digital outputs optocoupler ( passive )
connect external power supply with
pull-up resistor. Observe maximal

allowed power supply

- power on and allow RHE XX 30 min. warming-up.
- fill the sensor completely and bubble free with medium,
flush sensor RHM through with relatively high flowrate
for at least 15 minutes
- attention : avoid any temperature shock
( read manual in detail )

- shut off the flow with a ball valve properly

For small meter sizes ( RHM 015 - 03 )
two valves are recommended
- press the zero button and watch the
indication ( see manual )

- open valves, start pump etc. - meter is ready for measurement

- if the installation conditions are changed significantly, please
perform a new "zeroing"

START

Z. - Nr.

Blatt

Projekt

E08W-E
1 / 1

Gepr.

von

Datum

Erstellt :

08.08.2001

Kunde

Gepr.

Bearb.

Datum

Änderung :

H.G.Rudolph
M.Küppers

RHE 08

2,7 K

Wiring diagramm RHE 08 standard

External intrinsically safe
zeroing contact ( option ), is
subject of a separate EEx - certificate.

common connection ( 0 Volt )
for frequency / pulses and
digital outputs 1 to 3

digital output 3 ( passive )
function programmable

digital output 2 ( passive )
function programmable

digital output 1 ( passive )

function programmable

digital output ( passive )

for mass flow rate

frequency / pulses

external voltage

max. 30 VDC

analog output 1 ( active )
current loop : 0/4 - 20 mA
max. 1000 Ohm
analog output 2 ( active )

current loop : 0/4 - 20 mA

max. 1000 Ohm

digital input 2 ( passive )

function programmable

external voltage
max. 30 VDC

digital input 1 ( passive )
function programmable

Note :

EEx - version : In - and outputs ( connectors 15 to 27 )
are galvanically isolated.

Sensor connections ( 1 to 9 ) are intrinsically safe.

Not EEx - version : In - and outputs ( connectors 15 to 27 )

are galvanically isolated.
Sensor connections ( 1 to 9 ) are not intrinsically safe.

Drive coils

Temperature
Sensor PT100

Mass Flow Meter
Sensor RHM xx

cur

rent

(

open col

)

50 m

Pick-up coil 1

Pick-up coil 2

Screen to ground connection ONLY with
HT- SENSORS ( High Temperature ) !

( only with option EEx ! )

4
5

trin

lly

r E

x - v

24 VDC

115/ 230 VAC

HAZARDOUS AREA

SAFE AREA

Source ( 5 VDC )

Sens ( max. 5 VDC )

Ground

Aux. Input

N
L1

1
2

3
4
5

6
7

8
9

422 m

9 P

TD+ > RD+ Pin 4

RD+ < TD+ Pin 2

TD - > RD - Pin 7
RD - < TD - Pin 9

Host

- remove transport fixation bold
( if applicable ) and re-seal the

housing before operating

- at least one ball valve recommended
for zeroing

- Check : No error message / indication for transmitter ?

- Check : stable indication ( zero flow ) without error indication available ?

created by : [email protected] http://www.rheonik.de

Installation recommendations Changes without notice

RHM

Rheonik Installation Quick Guide

Содержание RHE 07



















































Результаты поиска

Содержание RHE 07

Отзывы:

Похожие инструкции для RHE 07

Бренды по названию

Популярные бренды

RHEONIK RHE 07, Руководство по эксплуатации

Результаты поиска

Содержание RHE 07

Отзывы:

Похожие инструкции для RHE 07

Бренды по названию

Популярные бренды