background image

PART IV 

TROUBLESHOOTING - NO FAN

E-21

No fan with incorrect display lights

When the unit is powered on, the display lights show incorrect and some buttons do not work properly.
Most of time, this problem is due to display circuit board wire loose.
1. Open the bottom plate, fasten the display circuit board wire connection.
2. Open the top plastic cover, fasten the connection of the display circuit board.

No fan with incorrect 
display lights

Fasten the display circuit board wire 
on the main circuit board.

Fasten the display circuit board 
wire on the display circuit board

Step 1

No fan with correct 
display lights

Step 2

ENGLISH

To find the display circuit 
board wire see IMPORTANT
PART-DISPLAY CIRCUIT 
BOARD on page 30.

No fan with correct display lights

The unit has correct display lights on the control panel but the fan does not work and the SPEED button also does not work 
correctly. Most of time, it is because of loose of the fan motor cable connection and the main circuit board problem.

Check if the fan motor cable connection is loosened

1. Put the unit on the table.
2. Open the bottom plate by removing 4 screws.
3. Inspect if the fan motor cable connection is tightly connected to the main circuit board. If the cable connection is loosened, fix 
it and try to press the SPEED button again. If the button still does not work properly, go ahead to check the output voltage from
the main circuit board to the fan motor. 

Open the bottom plate after 
removing 4 screws.

Fasten the fan motor cable 
connection to the main circuit board. 

Содержание 300T























































Отзывы: