RespirAide 300T Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 54

RespirAide 300T Скачать руководство пользователя страница 36

PART IV

TROUBLESHOOTING - NO POWER

E-36

Check power cord plug and outlet

1. Sometimes, the unit does not operate because of the electrical outlet failure. Check if other electrical appliances using the
same electrical outlet are working.
2. Make sure the power plug is inserted into the wall outlet correctly, or try to check if the power cord socket on the unit is
installed correctly.

Adjust interlock switch lever

If you are sure the front panel is closed properly but the unit still has no power, you will need to adjust the interlock switch lever.
1. Put the unit on the table.
2. Open the bottom plate after removing the 4 screws on the bottom plate.
3. Loosen the 2 screws on the interlock switch adjustor plate and adjust the height of the interlock switch so that the putter can
push down the interlock switch.

1. Make sure the power plug is
tightly inserted into the outlet.

2. Make sure the power plug is
tightly inserted into the unit power
socket.

3. Properly install the front panel.

4. Adjusting the interlock switch
adjustor with a screwdriver.

5. Cut down some of the plastic
lever on the interlock switch.

Check front panel

If the power cord is OK, go to check the front panel. There is an actuator at
the right bottom inside the front panel. The actuator must push down the
lever of the interlock switch to operate the unit. If the front panel is detached
or the actuator is deformed the unit does not work. You need to try to open
the front panel and firmly close again. Make sure there are no dents or
bends which would refrain from closing the front panel correctly.

ENGLISH

Check power cord plug and
outlet

Step 1

Check front panel

Step 2

Check interlock switch

Step 3

Actuator

Helpful hints

When you open the front panel the unit still
runs the interlock switch lever cannot spring
up. At this time, you need to cut some of the
interlock switch plastic lever with a knife.

«
...
34
35
36
37
38
...
»

Содержание 300T























































Отзывы:

Нет отзывов