REPLIGEN XCell Lab XC-LAB-D Скачать руководство пользователя страница 58

Страница: 58 / 69

XCell™ Lab Controller

User Guide

58 repligen.com XC-LAB-UG-V4

13.

Appendix C List of system-defined alarms

Alarm/Interlock

Event Trigger

System Response

System Configuration Error

Hardware configured is not

compatible with the system (i.e. the

following is invalid: filter size, fiber ID,

filter length, number of fibers, both

single and dual FT enabled, pressure

sensor config, save command is given

while filter is running)

The PLC cannot save

Diaphragm Command

Limited by Range

Flow rate entered is outside of the

system range

ATF controller restricts flow rate to

the minimum or maximum flow,

whichever is closer

Invalid Dual Mode

Command

Filter A and Filter B configuration do

not match

Dual Mode will not turn on

Loss of Pressure Supply

Pressure supply is absent

System maintains running at

current setpoint with no feedback

changes to the pressure curve

Loss of Vacuum Supply

Vacuum supply absent

System stops running

Filter A Flow Not Meeting

Setpoint

The average flow after 40 consecutive

cycles is less than 90% of the assumed

diaphragm displacement volume

System adjusts the pressure curve

to try to attain the setpoint

A2B Flow Sensor

Communication Error

One of the A2B flow sensors are not

communicating, usually due to a

disconnected cable

If the system is not running, it will

not be able to start process, if the

system is running when this alarm

occurs the system maintains

running at current setpoint with no

feedback changes to the pressure

curve

A2B Flow Sensor Data Error All flow sensors are properly

communicating, but one or more of

the A2B flow sensors have not

updated in 60 seconds or more (i.e.

not attached to the A2B line), or if

there is a mismatch of ±15% between

the two A2B flow sensors in dual A2B

mode

If the system is not running, it will

not be able to start process, if the

system is running when this alarm

occurs the system maintains

running at current setpoint with no

feedback changes to the pressure

curve

Permeate Flow Sensor

Communication Error

One of the permeate flow sensors are

not communicating, usually due to a

disconnected cable

N/A

Permeate Flow Sensor Data

Error

All flow sensors are properly

communicating, but one or more of

the A2B flow sensors have not

updated in 60 seconds or more (i.e.

not attached to the permeate line)

N/A

Содержание XCell Lab XC-LAB-D






































































Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды

REPLIGEN XCell Lab XC-LAB-D, Руководство пользователя

Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды