REPLIGEN XCell Lab XC-LAB-D Скачать руководство пользователя страница 31

Страница: 31 / 69

XCell™ Lab Controller

User Guide

31 repligen.com XC-LAB-UG-V4

Table 12. Starting, pausing and stopping XCell ATF® Device(s) in Dual Mode

Actions

In-phase

and out-of-

phase

Start

Open either the ATF-A or ATF-B flow Pop-

up , select mode for dual control and then

press

Start.

Pause

Software: Open either ATF -A or ATF-

B Flow Pop-up and press

Pause

Software: Press the

All Pause

buttons

on ATF Main screen

Hardware: Press either

Pause

button

on controller Face B (Figure 6)

Stop

Software: Press the

All Pause

buttons on

ATF Main screen

Start

1. Software: Open either ATF -A or ATF-B

Flow Pop-up and press

Pause

2. Hardware: Press either

Pause

button on

controller face B

Independent

Start

Open the relevant ATF flow Pop-up and

then press

Start.

Pause

Software: Open either ATF -A or ATF-

B Flow Pop-up and press

Pause

Software: Press the

All Pause

buttons

on ATF Main screenn to pause the

respective ATF unit (A or B) to pause.

For example if the all pause was

pressed for ATF B while running in

independent mode, then ATF B is

paused and ATF A continues to run.

Hardware: Press either

Pause

button on

controller Face B (

Figure 6

)

Stop

Press

Stop

on the

ATF Flow pop-up.

Upon

re-start, the controller starts without

utilizing previous settings. A

Stop

recommended to be used only at the end

of a run.

Note:

It is not possible to re-start in dual mode unless both ATFs are paused and re-started together.

Note:

After pressing STOP, the setpoint value remains the same, which is the only user editable

parameter. The most significant difference between STOP and PAUSE is that PAUSE keeps the

XCell ATF® Device in a hold position where it can resume when START is pressed a second time.

Pressing STOP stops the running session; when start is subsequently pressed it goes through

the start initiation process (Priming).

Содержание XCell Lab XC-LAB-D






































































Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды

REPLIGEN XCell Lab XC-LAB-D, Руководство пользователя

Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды