REPLIGEN XCell Lab XC-LAB-D Скачать руководство пользователя страница 10

Страница: 10 / 69

XCell™ Lab Controller

User Guide

10 repligen.com XC-LAB-UG-V4

About this document

This manual uses several user attention phrases. Each phrase should draw the following level of

attention:

Table 1. Explanation of user attention phrases

Phrase

Description

Note:

Points out useful information.

IMPORTANT Indicates information necessary for proper instrument operation.

PRECAUTION Cautions users of potential physical injury or instrument damage if the information is not

heeded.

WARNING!

Warns users of potential serious physical injury if warnings are not heeded.

Safety precautions

Table 2. Safety precautions examples

Description of precautions

Use of safety glasses is recommended during installation, set up, operation and while any service

or testing is being performed on the system.

You must use the Supply Air Protection Assembly (SAPA) on your air source to ensure air is

brought to a safe pressure, and suitably filtered to ensure pump functionality.

Vessels or bioreactors should not be pressurized unless otherwise specified by the manufacturer.

Glass and single-use bags can explode if pressurized. When using any vessel or bioreactor, be

sure to maintain an unrestricted vent or exhaust from the vessel. This will ensure that no

significant pressure or vacuum occurs in the bioreactor. In the case of a diaphragm failure, for

example, air will penetrate the XCell ATF® Device, through the filter and into the vessel. A free

exhaust from the vessel will minimize the build-up of pressure in the vessel.

You must replace the air filter on Stainless Steel XCell ATF® Devices (ATF2 and ATF4) prior to

operation.

When not in use, you should ensure all the tubing is capped or blocked using the provided caps

and valves. It is recommended to keep unused tubing in the original sealed bag.

Содержание XCell Lab XC-LAB-D






































































Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды

REPLIGEN XCell Lab XC-LAB-D, Руководство пользователя

Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды