REPLIGEN XCell Lab XC-LAB-D Скачать руководство пользователя страница 19

Страница: 19 / 69

XCell™ Lab Controller

User Guide

19 repligen.com XC-LAB-UG-V4

Table 6. A2B Tubing ID/OD

Device

Tubing ID /OD

Repligen Supplied Tube set?

XCell ATF® 1

1/8” / 1/4"

Yes, part of device

XCell ATF® 2

1/4” / 3/8”

Yes, supplied separately

XCell ATF® 4

3/8” / 5/8”

Yes, supplied separately

Please reach out to your local Repligen representative for more information.

6.6

Supply Air Protection Assembly (SAPA)

Figure 7. SAPA components example

Table 7. SAPA components

Item

Description

1 Manifold inlet

Pressurized air from air supply

2 Filter unit

Filters air routing from air supply to manifold

Filter porosity: 0.3

3 Pressure regulator

Factory set air pressure supply regulator designed to

downregulate the supply air to a lower pressure required to

operate XCell ATF® 1, XCell ATF® 2 and XCell ATF® 4 (do not

adjust)

4 Pressure relief valve

Factory set air supply pressure relief valve set to relieve if

inlet pressure exceeds the specification noted above (do not

adjust)

5 Positive pressure supply manifold

Pressurized air to XCell™ Lab Controller(s)

6 Manifold outlets

Distributes air pressure to up to four XCell™ Lab Controllers

The SAPA normalizes air pressure from the lab utility line down to the required 15.6 psi. The

minimum utility air pressure requirement is 30 psi. A pressure relief valve provides safety in case of

the unlikely failure of the regulator

(Figure 7)

. The regulator and relief valve are pre-set at the

factory; no modification is required by the end user. Installation should be performed or supervised

by an authorized Repligen service engineer.

Note:

The SAPA must be installed with the air filter oriented downwards and plumbed.

Содержание XCell Lab XC-LAB-D






































































Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды

REPLIGEN XCell Lab XC-LAB-D, Руководство пользователя

Результаты поиска

Содержание XCell Lab XC-LAB-D

Отзывы:

Бренды по названию

Популярные бренды