manualshive.com logo in svg

Renesas M16C/60 Series, Руководство пользователя

На нашем сайте Вы можете бесплатно скачать пользовательское руководство для серии продуктов Renesas M16C/60. Наши мануалы помогут Вам разобраться в функциях и возможностях данной продукции. Скачать можно на manualshive.com.

Поделиться
Скачать
background image

R01UH0136EJ0210 Rev.2.10

Page 77 of 800

Jul 31, 2012

M16C/64A Group

7.  Voltage Detector

7.4.3.2

Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset

Table 7.7 lists Procedures for Setting Voltage Monitor 1 Interrupt/Reset Related Bits.

When using voltage monitor 1 interrupt or voltage monitor 1 reset to exit stop mode, set the VW1C1
bit in the VW1C register to 1 (digital filter disabled).
When voltage monitor 1 reset is generated, the LVD1R bit in the RSTFR register becomes 1 (voltage
monitor 1 reset detected). Refer to 6.4.5 “Voltage Monitor 1 Reset” for status after reset.
Figure 7.6 shows Voltage Monitor 1 Interrupt/Reset Operation Example.

Table 7.7

Procedures for Setting Voltage Monitor 1 Interrupt/Reset Related Bits

Step

When Using the Digital Filter

When Not Using the Digital Filter

Voltage monitor 1 

interrupt

Voltage monitor 1 

reset

Voltage monitor 1 

interrupt

Voltage monitor 1 

reset

1

Set the VW12E bit in the VWCE register to 1 (voltage monitors 1 and 2 enabled).

2

Set bits VD1LS3 to VD1LS0 in the VD1LS register to select Vdet1.

3

Set the VC26 bit in the VCR2 register to 1 (voltage detector 1 enabled).

4

Wait for td(E-A).

5

Use bits VW1F1 and VW1F0 in the VW1C 
register to select the digital filter sampling 
clock.

Use the VW1C7 bit in the VW1C register to 
select the timing of the interrupt and reset 

request. 

(1)

6 

(2)

Set the VW1C1 bit in the VW1C register to 0 
(digital filter enabled).

Set the VW1C1 bit in the VW1C register to 1 
(digital filter disabled).

7 

(2)

Set the VW1C6 bit in 
the VW1C register to 0 
(voltage monitor 1 
interrupt).

Set the VW1C6 bit in 
the VW1C register to 1 
(voltage monitor 1 
reset).

Set the VW1C6 bit in 
the VW1C register to 0 
(voltage monitor 1 
interrupt).

Set the VW1C6 bit in 
the VW1C register to 1 
(voltage monitor 1 
reset).

8

Set the VW1C2 bit in the VW1C register to 0 (Vdet1 passage not detected).

9

Set the CM14 bit in the CM1 register to 0 (125 
kHz on-chip oscillator on)

-

10

Wait for digital filter sampling clock x 3 cycles. - (no wait time)

11

Set the VW1C0 bit in the VW1C register to 1 (voltage monitor 1 interrupt/reset enabled).

Notes:

1.

Set the VW1C7 bit to 1 (when VCC1 reaches Vdet1 or below) for the voltage monitor 1 reset.

2.

When the VW1C0 bit is 0, steps 5, 6, and 7 can be executed simultaneously (with one instruction).

3.

If above setting is performed while voltage monitor 1 interrupt/reset is disabled (VW1C0 bit in the
VW1C register is 0, VC26 bit in the VCR2 register is 0) and VCC1 < Vdet1 (or VCC1 > Vdet1) is
detected before enabling voltage monitor 1 interrupt/reset (step 11), an interrupt does not occur.
When VCC1 < Vdet1 (or VCC1 > Vdet1) is detected while executing steps 9 to 11, the VW1C2 bit
becomes 1.
When using this result detected between steps 9 and 11, read the VW1C2 bit after step 11. If the
bit is 1, execute the process to be performed after detecting the VCC1 < Vdet1 (or VCC1 > Vdet1).
When ignoring the result detected between steps 9 and 11, set the VW1C2 bit to 0 after step 11.

Содержание M16C/60 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M16C/60 Series

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Бренд: IEI Technology Страницы: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Бренд: IEI Technology Страницы: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Бренд: IEI Technology Страницы: 3
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Бренд: Opengear Страницы: 2
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Бренд: LGC wireless Страницы: 154
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Бренд: Accom Страницы: 15
Renesas H8/3864 Series User Manual preview
H8/3864 Series
Бренд: Renesas Страницы: 20
Tait TM9000 Installation Instructions Manual preview
TM9000
Бренд: Tait Страницы: 8
C4i GEN-1 Quick Operation Manual preview
GEN-1
Бренд: C4i Страницы: 5
Xantech CC12 Installation Instructions preview
CC12
Бренд: Xantech Страницы: 4
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Бренд: Lantronix Страницы: 10
ekwb EK-Quantum Vector FTW3 RTX 2080 Ti Installation Manual preview
EK-Quantum Vector FTW3 RTX 2080 Ti
Бренд: ekwb Страницы: 3
Rimage CDPR3 User Manual preview
CDPR3
Бренд: Rimage Страницы: 30
Allied Telesis AR440S Hardware Reference Manual preview
AR440S
Бренд: Allied Telesis Страницы: 44
ADLINK Technology ROScube-I Series User Manual preview
ROScube-I Series
Бренд: ADLINK Technology Страницы: 95
KWorld DVB-T 355U Faq preview
DVB-T 355U
Бренд: KWorld Страницы: 27
Sonnet TEMPO SATA E4i Quick Start Manual preview
TEMPO SATA E4i
Бренд: Sonnet Страницы: 8
DAQ USB-DIO6400 User Manual preview
USB-DIO6400
Бренд: DAQ Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды