Renesas IDT Tsi576 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 530

background image

2. Serial RapidIO Interface > Multicast Event Control Symbols

55

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

2.5

Multicast Event Control Symbols

Multicast-Event Control Symbol (MCS or MCES) forwarding describes the process where an MCS
received on one RapidIO port is propagated out other RapidIO ports.

When a RapidIO port receives an MCS, it signals all other ports of the fact that an MCS was received.
Each port can optionally transmit an MCS when it is notified that an MCS has been received by another
port. A port is forwarded an MCS when the MCS_EN bit is set in the

“RapidIO Serial Port x Control

CSR” on page 283

.

2.5.1

MCS Reception

When a RapidIO port receives a MCS, it does the following:

•

Raises an interrupt that can be masked.

— Interrupts are masked when the port’s MCS_INT_EN bit is set in

“RapidIO Port x Mode

CSR” on page 312

•

Forwards the symbol to all the other RapidIO ports

— Each port then forwards the control symbol if its MCS_EN field in the

“RapidIO Serial Port x

Control CSR” on page 283

is set to 1.

Per-port interrupt status appears in the MCS field in the

“RapidIO Port x Multicast-Event Control

Symbol and Reset Control Symbol Interrupt CSR” on page 314

. Additionally, the logical OR of all

per-port Multicast Event interrupt status is available in both the MCS field in the

“RapidIO Port x

Multicast-Event Control Symbol and Reset Control Symbol Interrupt CSR” on page 314

and the MCS

field in the

“Global Interrupt Status Register” on page 390

Interrupts can be cleared, either per-port or for all ports, by writing 1 to the MCS field in the

Port x Multicast-Event Control Symbol and Reset Control Symbol Interrupt CSR” on page 314

.

Additionally, the MCES pin in the Tsi576 can output an edge when an MCS is received. The MCES pin
toggles to signal an MCS is received; that is, the first MCS causes the pin to go low and the second
MCS causes it to go back high. The ports that are used as the source for toggling this MCES pin is
selectable using the MCS_INT_EN bit in the

“RapidIO Port x Mode CSR” on page 312

. To select the

MCES pin as an output, set the MCES_CTRL to 10 in the

“MCES Pin Control Register” on page 396

.

Ti

p

Multicast-Event control symbols (MCS) are explained in detail in the

RapidIO Interconnect

Specification (Revision 1.3)

.

Due to the finite time it takes to translate an MCS to a signal on the MCES pin, the minimum
time between any two MCS received in the Tsi576 is 500 ns. The second MCS can be lost if
this condition is not met.

«
...
53
54
55
56
57
...
»

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IDT Tsi576

Бренд: IBM Страницы: 88

Бренд: Raritan Страницы: 4

Бренд: Kramer Страницы: 8

Бренд: A-Neuvideo Страницы: 16

Бренд: Black Box Страницы: 9

Бренд: Racal Instruments Страницы: 33

Бренд: Advantech Страницы: 101

ISCOM2600G (A) Series

Бренд: Raisecom Страницы: 96

Бренд: AVLinx Страницы: 10

Бренд: Encore Страницы: 1

Бренд: WIKA Страницы: 76

Бренд: StarTech.com Страницы: 2

Бренд: MyQ Страницы: 24

Ultraview Remote 2

Бренд: Rose electronics Страницы: 58

Бренд: Larson Electronics Страницы: 2

Бренд: Idem Страницы: 2

Бренд: Planet Страницы: 16

Бренд: Planet Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды