Renesas IDT Tsi576 Скачать руководство пользователя страница 444 | Manualshive

Страница: 444 / 530

background image

13. I2C Registers > Register Descriptions

444

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

09:15

BOOT_ADDR

Boot Device Address

This is the device address that the Tsi576 will access during
the boot load sequence. The least significant two bits [14:15]
of this field are latched at power-up from the state of the
I2C_SA[1:0] pins. This allows board configuration of up to
four unique Tsi576 devices on the I2C bus, each of which
access a different EEPROM during boot load. These two
bits are then locked for writing until the BUNLK bit is set to 1
during a write. This feature allows the boot load process to
change the boot address value to this register without
changing the power-up latch field.

This field can be changed during the boot load in
conjunction with setting the CHAIN bit, in order to jump the
boot load to a new boot device. This starting address is
copied internally at boot start or boot load, and it is the
internal value that is incremented, as explained in the BINC
field.

R/W

Undefined

16:18

PAGE_MODE

Page Mode

000 = 8 bytes

001 = 32 bytes

010 = 64 bytes

011 = 128 bytes

100 = 256 bytes

101 = 512 bytes

110 = 1024 bytes

111 = Infinite

This field modifies the boot load process to adjust the
boundary at which the boot device is re-addressed. In the
default case, the boot load sequence reads 8 bytes, then
does a Restart followed by the device and peripheral
address phases. By changing this field, the device will be
re-addressed only when the peripheral address crosses the
indicated boundary, thus saving a considerable number of
clock cycles during the boot. It is up to the programmer of
the EEPROM to ensure that the addressed device can
support consecutive reads up to the selected boundary.
Some devices wrap at certain page boundaries, and this
setting must be consistent with such limitations.

A setting of 111 causes the entire boot load to be read
sequentially, with two exceptions. No matter what the setting
of this field, if the boot address is incremented due to the
BINC mode being enabled, or if chaining occurs, then the
device is readdressed.

Changing this field during boot load will immediately affect
the boot sequence.

R/W

000

(Continued)

Bits

Name

Description

Type

Reset

Value

«
...
442
443
444
445
446
...
»

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IDT Tsi576

Бренд: Fema Страницы: 96

Бренд: Dataprobe Страницы: 21

Бренд: DITEC Страницы: 8

Бренд: socomec Страницы: 43

AW-FGT-100C-120

Бренд: Vivotek Страницы: 2

Бренд: Gefen Страницы: 56

Бренд: F&F Страницы: 10

Бренд: Cabletron Systems Страницы: 170

Бренд: Canoga Perkins Страницы: 7

Бренд: GarrettCom Страницы: 77

Бренд: CableTronix Страницы: 4

LiteWave LS105G

Бренд: TP-Link Страницы: 3

Hi-Speed USB 4-Port Bay Hub

Бренд: SIIG Страницы: 8

Бренд: H3C Страницы: 70

iBootBar iBB-DC8

Бренд: Dataprobe Страницы: 36

Бренд: Hama Страницы: 36

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды