Renesas IDT Tsi576 Скачать руководство пользователя страница 258

Страница: 258 / 530

12. Serial RapidIO Registers > RapidIO Logical Layer and Transport Layer Registers

258

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

12.5.9

RapidIO Route LUT Size CAR

This register tells host software that the Tsi576 supports 512 destination IDs in its lookup table (LUT).
When the LUT_512 bit in the

“RapidIO Port x Mode CSR” on page 312

is set to 0, the corresponding

switch port supports 64K destination IDs with limited capabilities

Register name: RIO_LUT_SIZE

Reset value: 0x0000_01FF

Register offset: 0034

Bits

00:07

Reserved

08:15

Reserved

16:23

LUT_SIZE[0:7]

24:31

LUT_SIZE[8:15]

Bits

Name

Description

Type

Reset

Value

0:15

Reserved

16:31

LUT_SIZE

Lookup Table Size

Identifies the destination IDs that can be used to route packets through
the switch. Destination IDs 0x0000 to LUT_SIZE are valid.

Note: When the LUT_512 bit in

“RapidIO Port x Mode CSR” on

page 312

is set to 0, destination IDs 0x0000 to 0xFFFF are valid on the

corresponding port, regardless of the LUT_SIZE value.

0x01FF

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание IDT Tsi576

Отзывы:

Похожие инструкции для IDT Tsi576

Бренды по названию

Популярные бренды

Renesas IDT Tsi576, Руководство пользователя

Результаты поиска

Содержание IDT Tsi576

Отзывы:

Похожие инструкции для IDT Tsi576

Бренды по названию

Популярные бренды