Renesas IDT Tsi576 Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 530

Renesas IDT Tsi576 Скачать руководство пользователя страница 183

7. I

2

C Interface > Timeouts

183

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

•

Transaction timeout (see

C Byte/Transaction Timeout Register”

) – This timeout is disabled on

reset. It detects a situation where a master is keeping the bus for an extended period of time, as
measured from the Start to Stop condition. This timeout is available primarily to detect a violation
of the SMBus TLOW:SEXT time. The response to this timeout expiring is identical to a Byte
timeout, with the exception that the events are MTRTO or STRTO for the master or slave
respectively.

•

Boot timeout (see

C Boot and Diagnostic Timer”

) – This timeout detects a situation where the

boot load sequence has not completed in a reasonable time. This could occur if the EEPROM was
improperly programmed with an infinite chaining loop, the bus ownership is held by some other
device, or some other anomalous situation resulting in any of the time-outs above. If the boot
timeout expires before the normal end of the boot load sequence, the master interface reads until
the next data byte and drives a Stop condition on the bus. It then sets the BLTO event, which causes
a BL_FAIL interrupt status to get updated in the

C Interrupt Status Register”

. An optional

interrupt can also be sent to the Interrupt Controller if the BL_FAIL bit is enabled in the

Interrupt Enable Register”

. The boot_complete signal is asserted when the boot load timeout

expires. If the boot timeout is not desired, then the EEPROM programming should immediately
write the I2C_BOOT_DIAG_TIMER.COUNT to 0 to disable the timeout.

«
...
181
182
183
184
185
...
»

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды