manualshive.com logo in svg

Renesas IDT Tsi576, Руководство пользователя

Поделиться
Скачать
Renesas IDT Tsi576 Скачать руководство пользователя страница 153

7. I

2

C Interface > Tsi576 as I

2

C Slave

153

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

7.4.6

Master Data Transactions

After the peripheral address phase, if any, 0 to 4 bytes of data are read or written, followed by the Stop 
condition. The number of bytes to be transferred is set in the SIZE field of the 

“I

2

C Master Control 

Register”

 when the operation is started, the type of transaction (read or write) is set in the WRITE field 

of the same register, and the order of byte transfer is set in the DORDER field of the 

“I

2

C Master 

Configuration Register”

. 

For a write transaction, bytes are taken from the 

“I

2

C Master Transmit Data Register”

 based on 

DORDER and sent to the target device. Each byte must be ACKed by the device. If a NACK is 
received, the transaction is aborted with a Stop, an MA_NACK interrupt status in the 

“I

2

C Interrupt 

Status Register”

. An optional interrupt can also be sent to the Interrupt Controller if enabled in 

MA_NACK of the 

“I

2

C Interrupt Enable Register”

. 

For a read transaction, bytes are received from the target device and placed in the 

“I

2

C Master Receive 

Data Register”

 based on DORDER. Each byte is ACKed by the Tsi576, except for the final byte that is 

NACKed to tell the target device to stop sending data, followed by a Stop condition to idle the bus. 

Upon successful completion of a transaction, the MA_OK interrupt status is updated in the 

“I

2

C 

Interrupt Status Register”

. An optional interrupt can also be sent to the Interrupt Controller if enabled 

in MA_OK of the 

“I

2

C Interrupt Enable Register”

. 

7.5

Tsi576 as I

2

C Slave

The Tsi576 can operate as a slave device on the I

2

C bus. An external master device places a transaction 

on the bus with a device address that matches that programmed in the SLV_ADDR field of the 

“I

2

C 

Slave Configuration Register”

, or matches the fixed SMBus Alert Response address. The external 

master can then read or write to the Tsi576 through a small block of 256 addresses called the 

Tsi576

 

peripheral address space

, and do the following: 

•

Directly access limited status, read and write mailboxes

•

Configure some options related to the slave access

•

Indirectly read or write any other register in the Tsi576 that is accessible through the register bus

Figure 34

 shows the bus protocols for accessing the Tsi576 as a slave device. The general procedure 

requires the external master to address the Tsi576, set the peripheral address to a position within the 
Tsi576 peripheral address space, then write or read some number of bytes. A write is terminated with a 
Stop or Restart, and a read is ended when the master responds to a byte with a NACK. There is no limit 
to the number of bytes that can be read or written in one transaction. The Tsi576 increments the 
peripheral address pointer after each byte, and wraps within the 256 space (see 

“Slave Peripheral 

Addressing”

). Read and write transactions can be mixed by the external master issuing a Restart 

instead of a Stop, then sending a new transaction that addresses the Tsi576 (all writes must include the 
peripheral address byte). 

If the Tsi576 experiences a chip reset while it is writing to an EEPROM, the write does not 
complete and the data at the target EEPROM address may be corrupted. 

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды