Renesas IDT Tsi576 Скачать руководство пользователя страница 433

Страница: 433 / 530

13. I2C Registers > Register Descriptions

433

Tsi576 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

BL_OK

Boot Load OK

0 = Interrupt status not asserted

1 = Boot load sequence completed successfully

This will also be set if the boot loading was disabled at reset.

R/W1C

16:19

Reserved

0x0

SA_FAIL

Slave Access Failed

0 = Interrupt status not asserted

1 = Error detected during slave access transaction

A slave transaction addressed to the Tsi576 aborted.

R/W1C

SA_WRITE

Slave Write

0 = Interrupt status not asserted

1 = Internal register write performed

The

“Externally Visible I

C Internal Write Data Register”

was

written by an external master, invoking a write to an internal
register. This will not assert if slave writes are disabled
(WR_EN in the

“I

C Slave Configuration Register”

= 0).

R/W1C

SA_READ

Slave Read

0 = Interrupt status not asserted

1 = Internal register read performed

The

“Externally Visible I

C Internal Read Data Register”

was

read by an external master, invoking a read to an internal
register. This will not assert if slave reads are disabled
(RD_EN = 0 in the

“I

C Slave Configuration Register”

R/W1C

SA_OK

Slave Access OK

0 = Interrupt status not asserted

1 = Access completed successfully

The Tsi576 was addressed as a slave device and the
transaction completed without error.

R/W1C

MA_DIAG

Master Diagnostic Event

0 = Interrupt status not asserted

1 = Diagnostic event

R/W1C

25:26

Reserved

(Continued)

Bits

Name

Description

Type

Reset

Value

Содержание IDT Tsi576



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание IDT Tsi576

Отзывы:

Бренды по названию

Популярные бренды

Renesas IDT Tsi576, Руководство пользователя

Результаты поиска

Содержание IDT Tsi576

Отзывы:

Бренды по названию

Популярные бренды