Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 110

Страница: 110 / 128

Datamate 2200 O&M

Page 104

9.8 System Menu

The system menu provides the user access to configuring the following:

• time

• date

• password

• database/file management.

9.8.1 Set Date and Time

This menu when selected will provide the user with options to change and display

the date and/or time.

Using the SYSTEM MENU TREE enter Set Date or Set Time.

The following chart highlights the Set Date and Set Time feature.

Menu or Display Description

System

Set Date allows the user to confirm or set the Date.

1. Set Date

When ENTER is pressed the following will be displayed

Set Date

[mm/dd/yy]

2. Set Time

Set Time permits the user to confirm or set the Datamate 2200 to the time of day.

When ENTER is pressed the following will be displayed

Set Time

[hr/min/sec]

3. Display

Displays the system Date and Time, verifies the current time and date.

Date/Time

When ENTER is pressed the following will be displayed.

Time Date

[hr/min/sec] [mm/dd/yy]

9.8.2 Password Configuration

This menu when selected will provide the user with the option to change the

password for entry into the PROGRAM mode of the transmitter.

Using the SYSTEM MENU TREE enter the Password.

The following chart highlights the Password feature.

Menu or Display

Description

Password

This menu allows the user to view and change the password to the

1. Change Password

PROGRAM menu

When ENTER is pressed the following will be displayed

Change Password

[XXXXXXX]

2. View Password

Allows the user to view the password for the next lower access level.

When ENTER is pressed the following will be displayed

View Password

[XXXXXX]

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды