Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 11

Страница: 11 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Calibration

Diagnostic

Datamate 2200 O&M

Page 5

SECTION 2: READ THIS FIRST

2.1 Transmitter Area Classification

WARNING: IMPROPER INSTALLATION IN A HAZARDOUS ENVIRONMENT COULD

CAUSE AN EXPLOSION. INSTALL THE Datamate 2200 IN AN AREA COMPATIBLE

WITH THE HAZARDOUS ENVIRONMENT SPECIFIED ON THE APPROVALS TAG.

The Datamate 2200 has been tested by an independent third party laboratory and has

been found to meet the following standards:

FCC Part 15, Class A - Emissions

EN61326 (1977), Class A - Emissions

EN61326 - Industrial Location Immunity

Hazardous Area Approval:

CSA

Class I, Div 2, Group C and D

Class II, Div 2, Groups E, F, and G

Class III

2.2 Orientation and Mounting

Orient the transmitter so that the enclosure cover and the conduit openings are easily

accessible.

2.3 Temperature, EMI/RFI, Humidity, Vibration and Mechanical Shocks

The specified limits for the transmitter are as follows:

• Ambient temperature (with optional LCD) -4 to 140°F (-20 to 60°C)

• Ambient temperature (without optional LCD) -40 to 140°F (-40 to 60°C)

• EMI/RFI Class A digital device, pursuant to Part 15 of the FCC Rules

• Humidity: 10 to 100% condensing

• Vibration [Nonoperating 5g, 3 Axis, 10 sweeps from 10-800 Hz]

[Operating 2.5g, 3 Axis, 10 sweeps from 10-800 Hz]

• Mechanical Shocks [Nonoperating 100 shocks up to 30g/11ms]

[Operating 100 shocks up to 15g/11ms]

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Бренды по названию

Популярные бренды