Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 7

Страница: 7 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Calibration

Diagnostic

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Datamate 2200 O&M

Page 1

SECTION 1: WHAT YOU NEED TO USE THIS MANUAL

1.1 Introduction to the Datamate 2200

Red Seal Measurement

Coriolis Flow Transmitter

ed Seal Measurement

and its employees would like to express our thanks for

purchasing the

Datamate 2200 R

ed Seal Measurement

Flow Transmitter.

The Datamate 2200 is the most versatile Coriolis Flow Transmitter available. It is the first

transmitter with an open architecture platform and to employ Digital Signal Processing

(DSP), full software configuration and optional batching capabilities.

1.2 About This Manual

This instruction manual explains how to install, start up, troubleshoot and program the

Datamate 2200 for use with the R

ed Seal Measurement

Coriolis Force Flow meters. For

more information

about the R

ed Seal

easurement

transducer, consult the Transducer

Installation Guide (M600).

CAUTION: Improper installation could cause error in measurement or failure

of transmitter.

For safety purposes, please follow all instructions and adhere to all precautions outlines

in this manual to assure the best operation of the Datamate 2200.

1.3 Terminology

The term

transducer

sensor

refers to an R

ed Seal Measurement

Coriolis Force Flow

Meter (CFF™).

The term

transmitter

refers to a Datamate 2200 RSM Flow Transmitter.

1.4 Principle of Operation

The principle of operation applies directly to the transducer. For a complete explanation,

please consult the

Red Seal Measurement

Mass Flow Transducer Installation Guide (M600).

1.5 Optional LCD

The Datamate 2200 transmitter is available with an optional Liquid Crystal Display (LCD).

The LCD displays all functions of the transmitter and is fully configurable from the unit.

See FIgures 1.1, 1.2 and 1.3 for the different available configurations of the Datamate

2200.

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды