Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 67

Страница: 67 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Calibration

Diagnostic

Datamate 2200 O&M

Page 61

Menu or Display Description

Electronic Zero

Displays the current electronic zero and the standard deviation for the last

1. Elec. Zero

automatic zero. With the correct access (level 2) the user can modify the

Params

displayed ZERO value with the ^ and > keys.

Electronics Zero

[ SX.XXXXeSXX]

DEG

Pressing ENTER will display the standard deviation (StdDev) of the last

automatic zero. The StdDev cannot be modified by the user.

StdDev

[ SX.XXXXeSXX]

DEG

Electronic Zero

Displays the current zero and the standard deviation for the zero.

2. Zero Electronics ZERO: SX.XXXXeSXX DEG

SDEV: X.XXXXeSXX DEG

ENTER to Calibrate

CANCEL to Exit

Choices from this menu are ENTER to re-zero and CANCEL to exit.

While the Zero is performed the display will read:

Zeroing

When Zeroing is complete the new zero and the standard deviation is

displayed:

ZERO: SX.XXXXeSXX DEG

SDEV: X.XXXXeSXX DEG

CANCEL to Exit

Press CANCEL to Exit and remove any jumper at the input of the Datamate

2200

Zero

Displays the current transducer zero. The transducer zero is the zero offset

2. Transducer Zero contribution of the transducer and installation. The transducer zero is

determined by subtracting the electronic zero from the system zero.

Press ENTER to review and/or modify the transducer zero.

Transducer Zero

With the correct access (level 2) the user can modify the displayed ZERO

value with the ^ and > keys.

Transducer Zero

[SX.XXXXeSXX]

DEG

Zero

This menu allows the user to review and modify the System zero of the

3. System Zero

Datamate 2200.

The System zero is the combined zero offset of the electronics, transducer

and the installation when there is no flow.

Choices from this menu are Syst Zero Params, Zero System, and Exit.

System Zero

Displays the current system zero and the standard deviation for the last

1. Syst Zero

automatic zero. Neither value can be modified from this menu

Params

System Zero

[ SX.XXXXeSXX]

DEG

Pressing ENTER will display the standard deviation (StdDev) of the last

automatic zero. The StdDev cannot be modified by the user.

StdDev

[ SX.XXXXeSXX]

DEG

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды