Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 52

Страница: 52 / 128

Datamate 2200 O&M

Page 46

8.6.1 Transducer Tube Drive Test

The Datamate 2200 Coriolis Flow Transmitter incorporates a digital multimeter to provide

diagnostic information on the transducer. This display permits the user to view four (4)

diagnostic measurements from the transducer.

These measurements are

1. Drive Current (the measured AC current to the drive coil)

2. Sensor A voltage (the measured AC voltage from Sensor A)

Sensor voltages for transducer sizes 1/8

″

(m012) to 2

″

(m200) should be in the range

of 200mV ± 5mVrms. For 3

″

(m300) and 4

″

(m400) transducers this value should be

140mV ± 5mVrms.

3. Sensor B voltage (the measured AC voltage from Sensor B)

Sensor voltages for transducer sizes 1/8

″

(m012) to 2

″

(m200) should be in the range

of 200mV ± 5mV. For 3

″

(m300) and 4

″

(m400) transducers this value should be

140mV ± 5mVrms.

4. Drive Efficiency (a calculated value for determining drive efficiency)

If any value is out of range, it may suggest that the transducer tube driver is experiencing

difficulties in maintaining the sensor voltages and/or the setpoint for the sensor voltages

was not set to the optimum level as noted above.

8.6.2 Diagnostic Alarm Matrix

The diagnostic alarm matrix is highlighted in the following chart.

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды