Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 37

Страница: 37 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Calibration

Diagnostic

Datamate 2200 O&M

Page 31

SECTION 7: STARTUP

7.1 Power

NOTE: Access to field wiring and circuit board terminals is not required during

flow meter start-up or zeroing.

After wiring connections have been made (Section 3.5), power can be supplied to the

Datamate 2200 transmitter.

Start-up Mode:

During start-up and initialization, the following start-up indicators can be

observed:

• 4-20mA and pulse outputs go to undefined fallback levels

• The optional LCD on the cover reads for two seconds, “R

eal

easurement

Coriolis Flow Transmitter”

• The display on the HART

Communicator reads “Field device warming up”

• Alarm outputs are active

Operating Mode:

After startup, the optional LCD display will indicate process

measurements.

7.2 Startup with NexLink PC Software

Using Figure 5.6.1, complete wiring connections between the Datamate 2200 transmitter

and an IBM compatible PC with RS485 serial interface.
At the Datamate 2200 using the following MENU TREE enter Comm Ports
From the Main Display press <Enter>, <3. Program>, <1. View Measurements>,

<3. Program>, <3. Configuration>, <6. Outputs>, <5. Comm Ports>
Under Comm Ports select the following: Comm Port:

1-4

, Baud Rate:

9600

Parity: None, Data Bits:

, Stop Bits:

, Protocol:

Modbus

, Modbus Mode:

ASCII

, Unit

ID:

Select any number between 1-247.

NOTE: All Datamate 2200 transmitters in the blind configuration are

pre-programmed from the factory with ID number “247.” Any change to the

Unit ID or protocol, power to the Datamate 2200 is to be recycled for the change

to be acknowledged. The default password for NexLink: User ID: admin

Password: admin

To change the Unit ID for a blind unit, within the NexLink PC software in the Configuration

menu select <Outputs> and <Comm Port>.

Within the NexLink PC software, select the Comm Port pull-down menu from the Main

Menu and configure the setting to match the Datamate 2200 transmitter settings. When all

settings match, reboot the Datamate 2200 transmitter.

Within NexLink open up the “Comm Port” menu using the displayed icon, select

View Measurements under the “Process Variables” pull down menu. If the NexLink

is communicating with the Datamate 2200, the displayed measurement values will

correspond to the Datamate 2200 display. If no communication exists, the NexLink PC

software will respond with “Closing Comm Port.” If this occurs, re-check wiring and

communication settings.

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Бренды по названию

Популярные бренды