Red Seal Measurement Datamate 2200 Скачать руководство пользователя страница 43

Страница: 43 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Calibration

Diagnostic

Datamate 2200 O&M

Page 37

7.9 API

Datamate 2200 allows to measure density in degrees API. API gravity measures the

relative density of liquid petroleum products, where 10°API is equivalent to the specific

gravity of water. In order to provide these measurements, Datamate 2200 contains

Volume Correction Factor (VCF) tables

for several petroleum products as well as a

custom table that the user can load. The API correction tables provided are for 5 different

petroleum products at two different temperature references: 60°F and 15°C. The custom

table allows to input a maximum of 100 pairs of Temperature and VCF.

Fuel Oil (840) @ 60°F

Fuel Oil (840) @ 15°C

LPG (505) @ 60°F

LPG (510) @ 15°C

Gasoline (730) @ 60°F

Gasoline (730) @ 15°C

Kerosene (820.1) @ 60°F

Kerosene (820.1) @ 15°C

Light Lube Oil (878) @ 60°F

Light Lube Oil (878) @ 15°C

Custom Table

The standard temperature, i.e. the temperature at which the density of water is taken as

the reference to calculate specific gravity, will depend on the temperature unit selected

in the temperature configuration menu. If the temperature selected is °F, the standard

temperature will be 60°F and the reference density used will be 0.999042 g/cc. If the

temperature selected is °C, the standard temperature will be 15°C and the reference

density used will be 0.999129 g/cc.

NOTE: It is important to be consistent in selecting the correct temperature unit

that matches the Volume Correction Factor table. For example, if the temperature

unit is °F, but the VCF table selected is “Fuel Oil 840@15°C,” the degrees API and

Standard Volume measurements will not be correct.

If the measured process temperature is outside the range of the values given in the

correction table for the selected product class, the correction factor for the nearest

temperature in the table will be used.

Correction

Temperature

Factor

VCF

...

VCF

100

VCF

100

API Standard 2540 (1980).

Содержание Datamate 2200

































































































































Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды

Red Seal Measurement Datamate 2200, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Datamate 2200

Отзывы:

Похожие инструкции для Datamate 2200

Бренды по названию

Популярные бренды