red lion CUB 1, Руководство пользователя

Страница: 106 / 154

PAXC & I: COUNTER AUTO RESET *
PAXI & R: SETPOINT ON DELAY *
PAXI & R: SETPOINT OFF DELAY *
PAXI & R: SETPOINT HYSTERESIS *
PAXC & I: SETPOINT ASSIGNMENT
22
!
"
+55
./'8-
SETPOINT ACTION
+55
: When not using a setpoint, it should be set to +55 (no action).
!
"
. /*'
.%*8-
Select the display that the setpoint is to be assigned.
!
"
322
%&8-
SETPOINT VALUE
Enter the desired setpoint value. Setpoint values can also be entered in the
Quick Programming Mode when the setpoint is configured as 1*' in Module 3.
(See Module 2 for Exchange Parameter Lists explanation.)
!
"
*+
'!/8-
SETPOINT TRACKING *
If a selection other than NO is chosen, then the value of the setpoint being
programmed (“n”) will track the entered selection’s value. Tracking means that
when the selection’s value is changed (in the Quick Programming Mode), the
“n” setpoint value will also change (or follow) by the same amount.
!
"
"=
'F&8-
SETPOINT BOUNDARY TYPE
"= activates the output when the assigned display value ( ./'8- ) equals or
exceeds the setpoint value. #+ activates the setpoint when the assigned display
value is less than or equal to the setpoint.
!
"
*+
%'<8-
SETPOINT STANDBY OPERATION *
Selecting ;1% will disable low acting setpoints at a power up until the display
value crosses into the alarm “off” area. Once in the alarm “off” area, the
setpoint will function according to the configured setpoint parameters.
+55 #.'/" '+9' <+9*$
. /*' < /*' / /*' !.'1
866666
to
666666
%&8@
*+
./*'#$ </*'#$
%&8>
//*'#$
%&8? %&83
"= #+
;1% *+
With Timed Out action, the setpoint output activates when the
count value equals the setpoint value and deactivates after the
Time Out value. This action is not associated with Boundary
types. tOUt
With boundary action, the setpoint output activates when the
count value is greater than or equal to (for
';G = "= ) or less than
or equal to (for ';G = #+ ) the setpoint value. The setpoint output
will deactivate when the count value is less than (for ';G = "= )
or greater than (for ';& = #+ ) the setpoint value.
bOUNd
With Latch action, the setpoint output activates when the count
value equals the setpoint value. The output remains active until
reset. This action is not associated with Boundary types. LAtCH
For Counter Assignments:
With Timed Out action, the setpoint output cycles when the rate
value is greater than or equal to (for
';G = "= ) or less than or
equal to (for ';G = #+ ) the setpoint value. The Setpoint Time Out
(
'+9'8-
) and Setpoint On Delay ( '+*8- ) values determine the
cycling times.
tOUt
With Boundary action, the setpoint output activates when the
rate value is greater than or equal to (for
';G = "= ) or less than
or equal to (for ';G = #+ ) the setpoint value. The setpoint output
will deactivate (Auto reset) as determined by the hysteresis
value.
bOUNd
With Latch action, the setpoint output activates when the rate
value is equal to the setpoint value. The setpoint output remains
active until reset. If after reset, the rate value is greater than or
equal to (for
';G
=
"=
) or less than or equal to (for
';G
=
#+
) the
setpoint value, the output will reactivate.
LAtCH
For Rate Assignments:
!
"
2
";%8-
The hysteresis value is added to (for
';G = #+
), or subtracted from (for
';G =
"=
), the setpoint value to determine at what value to deactivate the associated
setpoint output. Hysteresis is only available for setpoints assigned to the Rate
with boundary action.
*
Factory Setting can be used without affecting basic start-up.
2
to
6666
!
"
2422
'+558-
This is the amount of time the Rate display must meet the setpoint
deactivation requirements (below hysteresis for high acting and above
hysteresis for low acting) before the setpoint’s output deactivates.
2422
to
66466 seconds
!
"
2422
'+*8-
This is the amount of time the Rate display must meet the setpoint activation
requirements (below setpoint for
';G = #+
and above setpoint for
';G = "=
) before
the setpoint’s output activates. If the Rate Setpoint Action is Timed Out, this is
the amount of time the output is off during the on / off output cycling.
2422
to
66466
seconds
!
"
3422
'+9'8-
SETPOINT TIME OUT *
If the setpoint action is Timed Out and the setpoint is assigned to Rate, then
this is the amount of time the output is on during the on / off output cycling. If
the setpoint action is Timed Out and the setpoint is assigned to Count, then this
is the amount of time the output will activate once the count value equals the
setpoint value.
!
"
*+
.9'+8-
This automatically resets the display value of the Setpoint Assignment ( .%*8
- ) counter each time the setpoint value is reached. This reset may be different
than the Counter’s Reset Action (x !1%1' ) in Module 1 or 5.
2422
to
66466 seconds
ZErOAE
*+ CLdAS ZErOAS
CLdAE
SELECTION ACTION
NO
No auto reset.
ZErOAS Reset to zero at the start of output activation.
CLdAS Reset to count load value at the start of output activation.
ZErOAE Reset to zero at the end of output activation. ( '+9' action only).
CLdAE Reset to count load value at the end of output activation. (
'+9'
action only).