Raven RoGator 64 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 80

background image

C

HAPTER

2

4

RoGator 64/74/86/SS Series AutoBoom Installation Manual

RECOMMENDATIONS

Raven Industries recommends the following best practices before installing or operating the AutoBoom system for

the first time, at the start of the season, or when moving the AutoBoom system to another machine:
• Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the machine’s

hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic hoses, etc.).

• Operate each of the machine’s boom hydraulic functions (i.e., tilt, fold, center rack, tongue extension, or other

hydraulic valve functions) three times to ensure the machine’s hydraulic valve is using fresh oil and debris is

flushed from the hydraulic hoses, valves, and filters.

• Upon installation of the AutoBoom system, operate the boom and center rack raise/lower functions through

the machine’s manual control functions first before operating them via the AutoBoom controller/field

computer to ensure the hydraulic system has been installed correctly and air is released from the system.

Raven Industries recommends the following best practices when installing the AutoBoom system.
• Use part numbers to identify the parts.
• Do not remove the plastic wrap from a part until it is necessary for installation.
• Do not remove plastic caps from a part until it is necessary for installation.

Tools Needed

The following tools are recommended for installation of the AutoBoom system:

• SAE standard-sized wrenches
• Cable ties
• Set of tools

POINT OF REFERENCE

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

«
...
6
7
8
9
10
...
»

Содержание RoGator 64 Series

















































































Отзывы:

Нет отзывов

Похожие инструкции для RoGator 64 Series

Бренд: Ravas Страницы: 4

Бренд: Taylor-Dunn Страницы: 180

Бренд: UralAZ Страницы: 146

Бренд: URAL Motorcycles Страницы: 247

Бренд: URAL Motorcycles Страницы: 267

Бренд: STAXX Страницы: 33

Бренд: Mobile Страницы: 13

Бренд: Mobile Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды