Raven RoGator 64 Series Скачать руководство пользователя страница 16

Страница: 16 / 80

HAPTER

RoGator 64/74/86/SS Series AutoBoom Installation Manual

INSTALL THE POWERGLIDE HYDRAULIC SYSTEM

INSTALL FITTINGS ON THE AUTOBOOM VALVE

Before mounting the AutoBoom valve on the machine, install the proper fittings on the valve. This prepares the

valve for installation and simplifies the hose connection process later in the procedure. Refer to the following

figure and table to install the fittings in the appropriate ports of the AutoBoom valve.

WARNING

The machine must remain stationary and

switched off, with the booms unfolded and

supported, during installation or maintenance.

CAUTION

When installing AutoBoom hydraulics or

performing diagnostics, maintenance, or routine

service, ensure precautions are taken to prevent

any foreign material from being introduced into

the machine’s hydraulic system.

Objects or materials that are able to bypass the

machine’s hydraulic filtration system will reduce

performance and possibly damage the

AutoBoom hydraulic valve.

NOTICE

The appearance of the AutoBoom hydraulic valve

may vary slightly from the images contained in

this manual. However, the fittings, hose

connections, and cable connections remain the

same.

Содержание RoGator 64 Series
















































































Результаты поиска

Содержание RoGator 64 Series

Отзывы:

Похожие инструкции для RoGator 64 Series

Бренды по названию

Популярные бренды

Raven RoGator 64 Series, Руководство по установке

Результаты поиска

Содержание RoGator 64 Series

Отзывы:

Похожие инструкции для RoGator 64 Series

Бренды по названию

Популярные бренды