Raven RoGator 64 Series Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 80

background image

C

HAPTER

5

66

RoGator 64/74/86/SS Series AutoBoom Installation Manual

b. Route and connect the orange wire to a source switched power.

NOTE:

Recommended locations are on the Raven controller or in the machine’s cab. Several Raven consoles

offer a +12V switched power connector on the console cable, which may be used to switch the circuit.

NOTE:

The instructions above apply to the installation of the 115-2001-041 cable in Falcon II ISO VT controller

kit.

CONNECT THE POWER LEADS

1. Locate the power cable that has the power and ground leads at one end.
2. Disconnect the machine’s connectors from the battery terminals.
3. Install the power lead on the positive battery terminal and reinstall the machine’s battery connector.
4. Install the ground lead on the negative battery terminal and reinstall the machine’s battery connector.

CONNECT THE CONTROLLER (IF APPLICABLE) - GEN I CABLE ONLY

1. Locate the two console cables (P/N 115-0230-005) and connect them to the AutoBoom console cable (P/N

063-0130-021).

2. Make the necessary CAN connections. Keep in mind there should be only two CAN terminators in the system,

one installed at each end of the CAN bus.

«
...
68
69
70
71
72
...
»

Содержание RoGator 64 Series

















































































Отзывы:

Нет отзывов

Похожие инструкции для RoGator 64 Series

Бренд: KION Страницы: 210

Бренд: Clark Страницы: 108

Бренд: Blue Giant Страницы: 24

Бренд: Blue Giant Страницы: 94

Бренд: Blue Giant Страницы: 118

Бренд: Blue Giant Страницы: 124

Бренд: Blue Giant Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды