Raven RoGator 64 Series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 80

Raven RoGator 64 Series Скачать руководство пользователя страница 68

C

HAPTER

5

64

RoGator 64/74/86/SS Series AutoBoom Installation Manual

11. Connect the ends of the installed boom sense adapter cable on the boom hoist down coil to the Center Down

Sense and Control connectors on the AutoBoom harness cable.

FIGURE 14. Connections

CONNECT THE HARNESS CABLE TO THE SENSORS

1. Locate the center sensor connector on the AutoBoom harness cable.
2. Connect the center sensor connector to the installed center sensor (P/N 063-0130-018).
3. Locate the left outer sensor connector on the AutoBoom harness cable.
4. Connect the left outer sensor connector to the installed left sensor cable (P/N 115-0171-0527).
5. Locate the right outer sensor connector on the AutoBoom harness cable.
6. Connect the right outer sensor connector to the installed right sensor cable.
7. If the optional boom sensors are installed, repeat step 1 to step 6 for the inner sensors.

CONNECT THE HARNESS CABLE TO THE IMPLEMENT EXTENSION TEE - GEN II CABLE ONLY

1. Route the harness cable (P/N 115-0230-085) toward the implement extension tee cable.
2. Connect the harness cable to the to node connector.
3. Remove the terminator from the machine’s chassis harness or the standalone console harness.
4. Install the terminator on the remaining open end of the implement extension tee cable.
5. Refer to the wiring schematic (beginning on page 67) appropriate for the machine’s configuration to route the

implement extension tee cable.

6. Connect the implement extension tee cable to the location determined in the step above.

«
...
66
67
68
69
70
...
»

Содержание RoGator 64 Series

















































































Отзывы:

Нет отзывов