Ransomes HR380 Скачать руководство пользователя

Страница: 59 / 128

en-59

OPERATION 7

7.3

OPERATING PROCEDURE

________________________________________________

1. Under no circumstances must the engine be started without the operator seated on the machine.

2. Do not operate machine or attachments with loose, damaged or missing components. Whenever possible

mow when grass is dry.

3. First mow in a test area to become thoroughly familiar with the operation of the machine and controls.

4. Study the area to determine the best and safest operating procedure. Consider the height of the grass, type of

terrain, and condition of the surface. Each condition will require certain adjustments or precautions.

5. Do not direct discharge of material toward bystanders, nor allow anyone near the machine while in operation.

The owner/operator is responsible for injuries inflicted to bystanders and/or damage to their property.

6. Use discretion when mowing near gravel areas (roadway, parking areas, cart paths, etc). Stones discharged

from the implement may cause serious injuries to bystanders and/or damage the equipment.Turn PTO cutter

switch off and raise the implements when crossing paths or roads. Look out for traffic.

7. Stop and inspect the equipment for damage immediately after striking an obstruction or if the machine begins

to vibrate abnormally. Have the equipment repaired before resuming operation.

8. Do not operate machine or attachments with loose, damaged or missing components.

WARNING

Never operate the equipment with the operator presence

& safety interlock system disengaged or malfunctioning.

Do not disconnect or bypass any switch.

CAUTION

To help prevent injury, always wear safety glasses, safety

footwear, a hard hat and ear protection

WARNING

Refer to machine Safe Working Slope Angles in

this manual

Test

Yes

Off

Neutral

Out of

Neutral

Yes

9
9

Lift your weight off the seat.

The engine must stop after 3 seconds.

Operator Seated

Park Brake Switch

Cutter Engage

(PTO) Switch

Traction Pedal

Engine Starts

Lift your weight off the seat. The cutting implement PTO will disengage within 3 seconds.

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды