Ransomes HR380 Скачать руководство пользователя

Страница: 85 / 128

en-85

MAINTENANCE AND LUBRICATION 8

8.11 BATTERY_________________________________________________________

Before you service the battery, make sure the ignition switch is in the OFF position and the key is removed.

Tighten the battery cables on the battery terminals, to prevent corrosion, apply a layer of silicone dielectric grease

to battery terminals and ends of cables. Keep the vent caps and battery terminal covers in position.

Before you do any welding operation on the mower, always disconnect

the battery cables from the battery and the connectors from the

controllers.

Confirm the battery polarity before you connect or you disconnect the

battery cables.

When you install the battery, always connect the positive (RED) battery

cable before the negative (BLACK) battery cable.

When you remove the battery, always disconnect the negative (BLACK) battery cable before the positive (RED)

battery cable.

Jump Starting the Mower

Before you try to jump-start the engine, check the condition of the drained battery.

Connect the positive (+) battery terminal of the charged battery to positive battery terminal of the drained
battery.

Connect the negative (–) battery terminal of the charged battery to frame of vehicle with the drained
battery.

When the cables are connected, start the engine on the vehicle with the good battery, then start the mower.

CAUTION

When you service the battery, always use the tools with insulation, wear protective glasses

and protective clothing.

Discard used batteries as Directed in your local regulations.

WARNING

The battery contains corrosive acid. Prevent contact with the battery acid.

Always wash your hands after you service a battery.

WARNING

The battery posts, battery terminals and related accessories contain lead and lead compounds,

chemicals know to the State of California to cause cancer and other reproductive harm.

WARNING

The battery can release hydrogen gas that is explosive. To decrease the risk of an explosion, prevent

sparks near the battery. Always connect the negative jumper cable to an appropriate ground

point with the drained battery.

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды