Ransomes HR380 Скачать руководство пользователя

Страница: 81 / 128

en-81

MAINTENANCE AND LUBRICATION 8

8.7

HYDRAULIC TEST PORTS__________________________________________

A hydraulic test port is positioned on the cutter valve to

allow the monitoring of the hydraulic cutting system.

If any problems are experienced with the hydraulic system

service ports are provided to enable pressures to be

checked.

All tests, unless stated otherwise, must be carried out with

the hydraulic oil at normal working temperature.

TEST PORT

A. Steering and lift pressure 125 bar.

NOTE:

Any hydraulic related issues contact your Ransomes Jacobsen dealer for a full fault diagnosis.

8.6

HYDRAULIC SYSTEM FLUSHING ____________________________________

When changing from mineral to vegetable oil

Terresolve™ EnviroLogic ® BioFlush is a carefully

designed fluid which helps to flush and remove

petroleum oil from hydraulic systems. This is done

when converting hydraulic systems to the use of

biodegradable fluids.

EnviroLogic ® BioFlush will condition the internal

hydraulic system to help optimize both overall

system performance and fluid biodegradability.

1. Run equipment until warm. Drain petroleum

hydraulic fluid and replace all hydraulic filters.

2. Fill system with EnviroLogic ® BioFlush. Run

equipment for 5 minutes until fluid is
completely circulated.

3. Drain the BioFlush and replace hydraulic

filters.

4. Fill system with approved biodegradable ISO

VG 46 hydraulic oil.

The hydraulic system is now optimised for fluid

biodegradability in the event of leakage.

When changing from vegetable to mineral oil there is no need to flush the system.

CAUTION

Dispose of used Hydraulic Oil

in accordance with local regulations.

CAUTION

Contact with Hydraulic Oil can damage your skin.

Use gloves when working with Hydraulic Oil. If

you come in contact with Hydraulic Oil, wash

it off immediately.

CAUTION

Pressurized Fluid can be extremely hazardous

and should be treated with caution. If Hydraulic

fluid injection occurs, seek immediate medical

attention. Always wear gloves and eye protection.

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды