Ransomes HR380 Скачать руководство пользователя

Страница: 21 / 128

en-21

SPECIFICATIONS 4

4.5

NOISE TESTING______________________________________________________

When the machine was tested for sound pressure (Operator Ear).

The Machinery Safety Directive 2006/42/EC

And

Exposure Of Workers To The Risks Arising From Physical Agents (Noise) Directive 2003/10/EC

By compliance to:

The Lawnmower Standard BS EN ISO 5395:2013

And

Sound Pressure Standard EN ISO 3746:2010

Measured Sound Pressure 88.6 dB(A) ± 1.06 LWA

Representative of worse case

When the machine was tested for sound power (Noise in the Environment).

The Machinery Safety Directive 2006/42/EC

And

Noise Emission In The Environment By Equipment For Use Outdoors

Directive 2000/14/EC

By compliance to:

Sound Power Standard EN ISO 3744:1995

160cm MUFM Out front flail Measured Sound Power 101 dB(A) ± 1.06 LWA

152cm Rear discharge deck Measured Sound Power 103 dB(A) ± 1.06 LWA

4.6

SLOPES ____________________________________________________________

DO NOT USE ON SLOPES GREATER THAN 19° FOR THE FLAIL UNIT AND 22° FOR THE ROTARY DECK.

This slope was calculated using static stability measurements according to the requirements of BS EN ISO 5395

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды