Ransomes HR380 Скачать руководство пользователя

Страница: 102 / 128

en-102

9 ADJUSTMENTS

9.8

AIR SUSPENSION SEAT (GRAMMER MSG75-521) _____________________

9.9.1

WEIGHT ADJUSTMENT ___________________________________________

The seat is adjusted for the driver’s weight by pulling or

pressing the lever for seat weight adjustment and with the

driver sitting on the seat.

The driver’s weight is adjusted correctly when the arrow is

in the middle clear area of the viewing window.

Within this viewing area, the individual height can be

adjusted to a minimum spring movement.

When the minimum/maximum weight adjustment has

been reached, you can hear it reaching the upper or lower

end stop.

To prevent damage to the health and material, the setting

for the driver’s weight must be checked and adjusted individually before the vehicle is driven.

In order to prevent compressor damage during weight

adjustment, the compressor must be operated no longer

than 1 minute.

9.9.2

FORE/AFT ADJUSTMENT _________________________________________

The fore/aft adjustment is released by lifting the locking

lever.

WARNING!

Risk of accident!

Do not operate the locking lever while driving.

WARNING!

Risk of crushing!

Only touch the lever at the indented grip, do not reach

back under the lever.

After the adjustment, the locking lever must latch into the

desired position with an audible click. It must not be

possible to move the driver’s seat into another position

when it is locked.

Do not lift the locking lever with your leg or calf.

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды